THS720: Difference between revisions

Jump to navigation Jump to search
4,649 bytes removed ,  16 October
off-loaded long lists to separate page
No edit summary
(off-loaded long lists to separate page)
Line 44: Line 44:


{{MissingSpecs}}
{{MissingSpecs}}
See [[THS720/Accessories]] for details on cables and other accessories.


==Operation==
==Operation==
Line 62: Line 64:


The analog scope section starts with an attenuator hybrid driven by four channels of HP (now Broadcom/Avago) optoisolators and NEC relays.   
The analog scope section starts with an attenuator hybrid driven by four channels of HP (now Broadcom/Avago) optoisolators and NEC relays.   
The hybrid contains the AC coupling capacitor and many laser trimmed resistors along with a custom Tek [[165-2545-00]] BGA.
The hybrid contains the AC coupling capacitor and many laser trimmed resistors along with a custom Tek chip ([[165-2545-00]]) in a BGA package.
The signal then passes through a single-ended to differential transformer and goes to a custom labeled Maxim two-channel high speed A/D converter [[234-1503-20]].
The signal then passes through a single-ended to differential transformer and goes to a custom-labeled Maxim two-channel high speed A/D converter ([[234-1503-20]]).
Note that the differential signal layout for channel 2 is not as good as channel 1 since one side of channel 2 goes through 2 vias not found on channel 1.
Note that the differential signal layout for channel 2 is not as good as channel 1 since one side of channel 2 goes through 2 vias not found on channel 1.
These optoisolators sometimes drift, causing a DC offset issue. They can be directly replaced with Broadcom/Avago part number HCNR201 (any of the -300E, -500E, -350E, or -550E variants will work) which are still readily available.
These optoisolators sometimes drift, causing a DC offset issue. They can be directly replaced with Broadcom/Avago part number HCNR201 (any of the -300E, -500E, -350E, or -550E variants will work) which are still readily available.
Line 73: Line 75:
NOTE: A THS710STD can be upgraded to a THS720STD, but due to main board differences, these models CANNOT be upgraded to a -A or -P model<br>
NOTE: A THS710STD can be upgraded to a THS720STD, but due to main board differences, these models CANNOT be upgraded to a -A or -P model<br>
Additionally, lower model scopes cannot be upgraded to a THS730A due to different input hybrid modules being used in the THS730A to provide the increased bandwidth.
Additionally, lower model scopes cannot be upgraded to a THS730A due to different input hybrid modules being used in the THS730A to provide the increased bandwidth.
==Replacement Accessories==
The DMM leads can be replaced with Mueller parts as used in the original lead kits 012-1482-00 for the standard set and ATLDX1 for the deluxe set as follows:
012-1482-00 DMM lead set contents (Mueller Electric part numbers):
* BU-4061-M-39-0 - UL Listed, Threaded Test Probe to Banana, Silicone - Black
* BU-4061-M-39-2 - UL Listed, Threaded Test Probe to Banana, Silicone - Red
* BU-60TBO - Steel Alligator Clip with #8-32 Threaded Barrel (Two needed)
* BU-62-0 - Insulator for BU-60 and BU-61 Series Clips - Black
* BU-62-2 - Insulator for BU-60 and BU-61 Series Clips - Red
* BU-00207-0 - Threaded Plunger Clip - Black
* BU-00207-2 - Threaded Plunger Clip - Red
ATLDX1 DMM lead set contents (Mueller Electric part numbers):
* BU-6161-M-39-0 - UL Listed, Test Lead Shrouded Banana Plugs Both ends Silicone - Black
* BU-6161-M-39-2 - UL Listed, Test Lead Shrouded Banana Plugs Both ends Silicone - Red
* BU-26101-0 - UL Listed, Test Probe Tip, Banana Plug Connection - Black
* BU-26101-2 - UL Listed, Test Probe Tip, Banana Plug Connection - Red
* BU-20431-0 - Right-angle Banana Jack, Hook Plunger - Black
* BU-20431-2 - Right-angle Banana Jack, Hook Plunger - Red
* BU-20433-0 - Flexible Rubber Coated Wire Grabber, Long - Black
* BU-20433-2 - Flexible Rubber Coated Wire Grabber, Long - Red
The cigarette lighter adapter is a standard 1.8m (6 foot) long cigarette lighter plug to 5.5mm x 2.1mm (Type A) center positive DC 'coaxial power connector' plug with red led and 1 A fuse.
The console cable and adapter, part numbers 012-1364-00 and 103-0403-00 can be replicated using an 8p8c RJ45 to female DB9 rewireable adapter and a 2 M long 8-conductor telephone type cable (wired pin 1 to 1, 2 to 2, etc) or Cat-5 Ethernet cable with a ferrite clipped near one end, sourced from ebay or the like.
The pinout for the adapter is as follows:
{| class="wikitable"
|-
! RJ45 !! Wire Color !! Function !! DB9 (female)
|-
| 1 || Brown || DCD- Data Carrier Detect || 7 - RTS
|-
| 2 || Blue || DSR- Data Set Ready || 4 - DTR
|-
| 3 || Yellow || DTR - Data Terminal Ready || 6 - DSR
|-
| 4 || Green || GND - Signal Ground || 5 - GND
|-
| 5 || Red || RXD - Receive Data || 3 - TXD
|-
| 6 || Black || TXD - Transmit Data || 2 - RXD
|-
| 7 || Orange || CTS - Clear To Send || 7 - RTS
|-
| 8 || Grey || RTS - Request To Send || 1&8 - DCD/CTS
|}
==Included Accessories==
* [[P6113B]] - 10X, 100 MHz, CAT II, 300 V<sub>RMS</sub> Passive probes (THS710STD, THS720STD)
* [[P6117]] - 10X, 200 MHz, CAT II, 300 V<sub>RMS</sub> Passive probes (THS730A, THS720A, THS710A)
* [[P5102]] - 10X, 100 MHz, CAT II, 1000 V<sub>RMS</sub> Passive probes (THS720P)
* 012-1482-00 - Meter lead set
* THS7BAT - 4.8 V, 2.8 Ahr Ni-Cd Battery pack
* AC Power Adapter
** 119-4812-XX - North America
** 119-4813-XX - Universal European
** 119-4922-XX - United Kingdom
** 119-4923-XX - Japan
* 012-1364-00 - 2m RS-232 cable (8p8c RJ45 'console cable')
* 103-0403-00 - 9-pin adapter (8p8c RJ45 to DB-9 adapter)
* 016-1399-00 - Soft case
* 070-9247-XX - User manual (THS710STD, THS720STD)
* 070-9731-XX - User manual (THS730A, THS720P, THS720A, THS710A)
* 070-9257-XX - Reference manual (THS710STD, THS720STD)
* 070-9741-XX - Reference manual (THS730A, THS720P, THS720A, THS710A)
==Optional Accessories==
* [[P5102]] - 10X, 100MHz, CAT II, 1000 V<sub>RMS</sub> Passive probes (THS730A, THS720A, THS710A, THS710STD, THS720STD)
* 012-1483-00 - Deluxe meter lead set (THS710STD, THS720STD)
* ATLDX1 - Deluxe meter lead set (THS730A, THS720P, THS720A, THS710A)
* THS7CHG - Battery charger
* THS7BAT - Extra 4.8 V, 2.8 Ahr Ni-Cd Battery pack
* 103-0090-00 - BNC to banana jack adapter to convert external trigger input to BNC (THS730A, THS720P, THS720A, THS710A)
* 174-1734-00 - Cigarette lighter adapter
* HC 411 - Thermal printer (006-7580-00 - Pack 5 paper rolls)
* THS7HCA - Hard carrying case
* [[A621]] - BNC Current Probe, AC only, 2000 A max, 5Hz to 50 kHz
* [[A622]] - BNC Current Probe, AC or DC, 100 A max, DC to 100 kHz
* [[A605]] - DMM busbar-style current probe, AC only, 500A max, 48 Hz to 1 kHz, 1 mV/A
* A610 - DMM busbar-style current probe, AC or DC, 500A max, DC to 440 Hz, 1 mV/A
* [[P6129B]] - 1X-10X, 10 MHz/100 MHz Switchable passive probes
* P6561AS - 10X, 100 MHz SMD probes
* [[P6408]] - Word Recogniser Trigger Probes - 16-bit word recogniser probe (trigger event recognition only)
* S60DWAV - DocuWave DOS software (THS710STD, THS720STD)
* WSTR31 - WaveStar software (THS730A, THS720P, THS720A, THS710A)
* 070-9245-XX - Programmer manual (THS710STD, THS720STD)
* 070-9751-XX - Programmer manual (THS730A, THS720P, THS720A, THS710A)
* 070-9246-XX - Service manual (THS710STD, THS720STD)
* 070-9752-XX - Service manual  (THS730A, THS720P, THS720A, THS710A)


==Software==
==Software==
Line 229: Line 135:
THS7CHG_Internal.jpg|Battery Charger Internal
THS7CHG_Internal.jpg|Battery Charger Internal
</gallery>
</gallery>
==Components==
{{Parts|THS720}}


[[Category:THS series scopes]]
[[Category:THS series scopes]]

Navigation menu