067-0502-01: Difference between revisions
No edit summary |
m (Capitolize sidebar summary) |
||
(4 intermediate revisions by 3 users not shown) | |||
Line 4: | Line 4: | ||
|class=Signal generator | |class=Signal generator | ||
|series= | |series= | ||
|summary=Amplitude | |summary=Amplitude Calibrator | ||
|image=Tek 067-0502-01.JPG | |image=Tek 067-0502-01.JPG | ||
|caption= | |caption= | ||
Line 11: | Line 11: | ||
|designers= | |designers= | ||
|manuals= | |manuals= | ||
* [[Media:062-1105-00.pdf|Tektronix 067-0502-01 Manual]] (OCR) | |||
* [[Media:062-1105-00.pdf|Tektronix 067-0502-01 Manual]] ( | |||
}} | }} | ||
The '''Tektronix 067-0502-01 Amplitude Calibrator and Comparator''' is an instrument that can be used to produce a reference rectangle voltage or current waveform and/or to compare an external unknown input with an internal or external reference. | The '''Tektronix 067-0502-01 Amplitude Calibrator and Comparator''' is an instrument that can be used to produce a reference rectangle voltage or current waveform and/or to compare an external unknown input with an internal or external reference. | ||
Line 24: | Line 23: | ||
See the [[067-0502-00]] page for a comparison of the -00 and -01 models. | See the [[067-0502-00]] page for a comparison of the -00 and -01 models. | ||
The HV supply uses a tube V427, to regulate the +300V supply. The manual lists V427 as a [[7734]], a triode-pentode, however some models contain a small circular adapter board (670-1860-00,388-2423-00) to adapt the [[B9A_base|noval tube socket]] to a [[Compactron_base|Compactron socket]] and use a [[6G11]] double pentode instead. The adapter PCB connects the screen grid and plate of the beam power tube together in a triode configuration. These models also have [[6G11]] printed below V427 on the chassis. | The HV supply uses a tube V427, to regulate the +300V supply. The manual lists V427 as a [[7734]], a triode-pentode, however some models contain a small circular adapter board (670-1860-00, 388-2423-00) to adapt the [[B9A_base|noval tube socket]] to a [[Compactron_base|Compactron socket]] and use a [[6G11]] double pentode instead. The adapter PCB connects the screen grid and plate of the beam power tube together in a triode configuration. These models also have [[6G11]] printed below V427 on the chassis. | ||
The output amplitude can be reduced down to 0.2 μV using the [[067-0529-00]] 1000:1 precision divider. | The output amplitude can be reduced down to 0.2 μV using the [[067-0529-00]] 1000:1 precision divider. | ||
{{BeginSpecs}} | {{BeginSpecs}} | ||
{{Spec | Output | {{Spec | Output | DC+, DC-, Squarewave}} | ||
{{Spec | Amplitude | {{Spec | Amplitude range | 0.2 mV to 100 V in 1-2-5 sequence, 5mA in current loop}} | ||
{{Spec | Amplitude | {{Spec | Amplitude accuracy | Within 0.25% into 1 MΩ load}} | ||
{{Spec | Squarewave | {{Spec | Squarewave repetition rate | 1 kHz within 20% }} | ||
{{Spec | Maximum | {{Spec | Maximum input voltage | 100 V }} | ||
{{EndSpecs}} | {{EndSpecs}} | ||
==Links== | |||
* [https://www.youtube.com/watch?v=a1uvoqf4wLc Tektronix 067-0502-01 Repair and Calibration] | |||
==Pictures== | ==Pictures== |
Latest revision as of 20:47, 15 November 2023
The Tektronix 067-0502-01 Amplitude Calibrator and Comparator is an instrument that can be used to produce a reference rectangle voltage or current waveform and/or to compare an external unknown input with an internal or external reference.
The output voltage is only accurate if terminated in 1 MΩ, the 50 V setting will experience the highest error if not properly terminated (0.5% in an open load).
The comparison is performed using an Airpax A175 chopper to switch between the two voltages that are being compared. The resulting output is a rectangular waveform with amplitude equal to the difference of two voltages. This waveform can be amplified using a drift-free AC amplifier and viewed on an oscilloscope for high sensitivity comparison.
See the 067-0502-00 page for a comparison of the -00 and -01 models.
The HV supply uses a tube V427, to regulate the +300V supply. The manual lists V427 as a 7734, a triode-pentode, however some models contain a small circular adapter board (670-1860-00, 388-2423-00) to adapt the noval tube socket to a Compactron socket and use a 6G11 double pentode instead. The adapter PCB connects the screen grid and plate of the beam power tube together in a triode configuration. These models also have 6G11 printed below V427 on the chassis.
The output amplitude can be reduced down to 0.2 μV using the 067-0529-00 1000:1 precision divider.
Key Specifications
Output | DC+, DC-, Squarewave |
---|---|
Amplitude range | 0.2 mV to 100 V in 1-2-5 sequence, 5mA in current loop |
Amplitude accuracy | Within 0.25% into 1 MΩ load |
Squarewave repetition rate | 1 kHz within 20% |
Maximum input voltage | 100 V |
Links
Pictures
-
067-0502-01
-
067-0502-01 Schematic
-
067-0502
-
067-0502-01 rear
-
067-0502-01 bottom
-
067-0502-01 front
-
067-0502-01 internal view
-
067-0502-01 internal detail with 6G11 as V427
Some Parts Used in the 067-0502-01
Part | Part Number(s) | Class | Description | Used in |
---|---|---|---|---|
6G11 | 154-0660-00 | Vacuum Tube (Pentode) | double sharp cut-off beam power pentode | 125 • 132 • 519 • 067-0502-01 • 050-0551-00 |