Connectors: Difference between revisions

From TekWiki
Jump to navigation Jump to search
m (added "an" to keep S-1 from wrapping)
 
(78 intermediate revisions by 7 users not shown)
Line 1: Line 1:
Tektronix equipment makes use of a wide variety of connectors. 
Tektronix equipment makes use of a wide variety of connectors, most of which follow established standards, but occasionally,
Most of the connectors were standard parts when the instruments were designed.
custom connectors were designed.  This page presents a partial overview of connectors used in Tektronix equipment.
Occasionally custom connectors were designed.  What follows is a partial list of connectors
used in Tektronix equipment.


==BNC==
For details, please see the pages linked from the headings.
BNC is the most common connector for measurement equipment up to 1GHz.
__TOC__
It is available in different impedances.  50-ohm is the most common.
==Coaxial connectors==
Tektronix gear transitioned from UHF connectors to BNC connectors in
the early 1960's.  For some pieces of equipment, a conversion kit was
available.


==SMA==
{| class="wikitable"
SMA connectors are good to about 20GHz.  The male connectors have a protruding center
|-
pin and ground shroud that screws on.  They are similar to UHF connectors, but much smaller
!colspan="2" | [[BNC connector]]
and with much tighter tolerances and better controlled impedance. The female is threaded
!colspan="2" | [[Tekprobe BNC connector]]
on the outside.
|-
| [[File:Bnc female.jpg|150px|thumb|BNC Female]]
| [[File:Bnc male.jpg|150px|thumb|BNC Male]]
| [[File:Tekprobe_connector.jpg|150px|thumb|Tekprobe connector (socket)]]
| [[File:Tekprobe_2_interface.png|150px|thumb|Tekprobe-BNC interface]]
|-
!colspan="2" | [[SMA connector]]
!colspan="2" | [[SMB connector]]
|-
| [[File:Sma male.jpg|150px|thumb|SMA Male]]
| [[File:Sma female.jpg|150px|thumb|SMA Female]]
| [[File:Smb on 4s1 sampler.jpg|150px|thumb|SMB Connector as Strobe Input to [[4S1]] Sampler]]
| [[File:Smb in tek 284.JPG|150px|thumb|SMB Connector as Tripper Pulse Input to [[284]] Tunnel Diode]]
|-
!colspan="2" | [[3.5 mm connector]]
!colspan="2" | [[2.92 mm connector]]
|-
| ''3.5 mm female image needed''
| [[File:3r5male.jpg | 150px | thumb | 3.5 mm male]]
| [[File:2r92fem.jpg | 150px | thumb | 2.92 mm female]]
| [[File:2r92male.jpg | 150px | thumb | 2.92 mm male]]
|-
!colspan="2" | [[UHF connector]]
!colspan="2" | [[N connector]]
|-
| [[File:UHF_socket.jpg|150px|thumb|UHF socket (on a [[G|Type G]] plug-in)]]
| [[File:013_045_5.jpg|150px|thumb|The 013-045 has one male two female UHF connectors]]
| [[File:N connector.jpg|150px|thumb|]]
| [[File:N socket.jpg|150px|thumb|]]
|-
!colspan="2" | [[GR-874 connector]]
!colspan="2" | [[BSM connector]]
|-
| [[File:Gr874 connector.jpg|150px|thumb|GR-874 cable connector]]
| [[File:S1-crop.jpg|150px|150px|thumb|GR-874 connector on an [[S-1]] sampling head]]
| [[File:7t11 bsm.jpg|150px|thumb|BSM female on front lower right of 7T11]]
| [[File:Bsm panel jack.jpg|150px|thumb|BSM panel jack]]
|-
!colspan="2" | [[Gremar connector]]
!colspan="2" | [[Peltola connector]]
|-
|colspan="2" align="center" | [[File:5t1a_coax_interconnect.jpg|150px|thumb|center]]
| [[File:Peltola-connector-socket.jpg |150px|thumb|Socket]]
| [[File:Peltola-connector-tip.jpg |150px|thumb|Tip]]
|-
!colspan="2" | [[TNC connector]]
!colspan="2" |  
|-
| [[File:Tnc-female-bulkhead-connector.jpg|150px|thumb|TNC Female]]
| [[File:Tnc-male-crimp-connector.jpg|150px|thumb|TNC Male]]
|  
|  
|-
|}


==SMB==
''See also '''[http://ecee.colorado.edu/~kuester/Coax/connchart.htm Coax connector comparison]''' ''
SMB connectors are small snap-on RF connectors developed in the 1960's.
They come in 50-ohm and 75-ohm variants. Their RF performance in somewhat
inferior to SMA connectors, but they are more compact and have the convenience
of being snap-on instead of having a screw-on grounding nut.


==GR-874==
==Fiberoptic connectors==
The GR-874 is a hermaphroditic RF connector developed by General Radio in the
late 1940's.  They are typically 50 ohms, but other impedances were available
using the same ground shield and housing, but different center pin geometry.
The Tektronix [[519]] uses a 125-ohm GR-874 connector which has a much thinner
center pin.  The regular 50-ohm version is used in the [[1S1]], [[1S2]],
[[3S1]], [[3S7]], [[4S1]], [[4S2]], [[5T1]], [[5T1A]], [[S1]], [[S2]],
and [[113]].


==Peltola==
{| class="wikitable"
The Tektronix website says the following about Peltola connectors:
|-
!colspan=2| [[FC/PC connector]]
|-
|-
| [[File:FCPC-connector.jpg |150px|thumb]]
|
|-
|}


<blockquote>
==Non-coaxial low-voltage connectors==
The Peltola connector was developed for in-house use by Tektronix (and developed by Ron Peltola).
However, the pieces to make the connector are these:


The Male coaxial connector consists of the RG-174 coax center conductor as the male pin, with the braided shield pressed between two eyelets, part number 210-0775-00 (smaller one) and part number 210-0774-00 (larger one). The outer eyelet is then "dimpled" to secure the eyelet-shield-eyelet combination.
{| class="wikitable"
|-
!colspan=2| [[Banana connector]]
!colspan=2| [[LEMO S-series connector]]
|-
| [[File:Banana plug.jpg|150px|thumb|Banana plug (original style)]]
| [[File:Banana jack.jpg|150px|thumb|Banana jack (Ext H input on [[502]])]]
| [[File:Lemo connector.jpg|150px|thumb|LEMO S-series male (on [[P6201]])]]
| [[File:Tek_7104_probe_power.jpg|150px|thumb|Probe power connector on rear panel of [[7104]]]]
|-
!colspan=2| [[GPIB connector]]
!colspan=2| [[Amphenol 165 series connectors]]
|-
| [[File:Gpib-connector.jpg|150px|thumb|GPIB connector on back of a Tektronix [[TDS210]] scope]]
| [[File:IEEE488_cable.jpg|150px|thumb|Stacking GPIB cable connector]]
| [[File:Tek 175 rear connector.jpg|150px|thumb|Rear Connector on [[175]]]]
| [[File:Tek 575 rear connector.JPG|150px|thumb|Rear Connector on [[575]]]]
|-
!colspan=2| [[XLR connector]]
!colspan=2| [[0.1" header]]
|-
| [[File:XLR connectors.jpg|150px|thumb| 3-pin XLR cable plug and socket]]
| [[File:XLR5_socket.jpg|150px|thumb| 5-pin XLR panel socket]]
| [[File:0.1in headers.jpg|150px|thumb| 0.1" pin headers with cable connectors]]
|
|-
!colspan=2| [[D-sub connector]]
!colspan=2|
|-
|
|
|
|
|-
|}


The Female (circuit board mounted) connector consists of 2 pieces. In the center is the socket pin connector, part number 136-0252-07 and the connector recepticle (with 3 circuit board mounting tabs), part number 131-1003-00.
==Power connectors==
</blockquote>


==UHF==
{| class="wikitable"
The UHF connector is basically a [[Connectors#Banana|banana]] connector with a screw-on shield.
|-
The male is often called a PL-259, and the female is often called an SO-239. Although it is
!colspan=2| [[IEC connector]]
called a "UHF" connector, the connector's construction does does not provide a standard controlled
!colspan=2| [[Octal connector]]
impedance, so it typically used up to 300 MHz, at most.  The design has been used since the 1930's,
|-
and it is used on many pieces of early Tektronix gear. Tek moved away from them in the mid-1960's.
| [[File:IEC.jpg|150px|thumb|IEC 320 (60320) C14 power inlet]]
Tek provided kits that allowed owners or field technicians to convert instruments from UHF connectors
| [[File:IEC320C13.jpg|150px|thumb|IEC 320 (60320) C13 cable plugs]]
to [[Connectors#BNC|BNC connectors]], which are smaller, quicker to attach and remove, and have better
| [[File:Octal plug.jpg|150px|thumb|Modern octal cable plug]]
high-frequency characteristics (controlled impedance).
| [[File:Octal_power_socket.jpg |150px|thumb| Octal power sockets on [[160]] series modules]]
|-
!colspan=2| [[NEMA 5-15 connector]]
!colspan=2| [[NEMA 1-15 connector]]
|-
| [[File:NEMA 5-15 on 549.jpg|150px|thumb|NEMA 5-15 ("Edison"), recessed]]
| [[File:NEMA 5-15 on 585.jpg|150px|thumb|NEMA 5-15 ("Edison")]]
| [[File:Tek514-lineSocket.jpg|150px|thumb|NEMA 1-15]]
|
|}


==Banana==
==Links==
According to Wikipedia, the banana connector was invented in 1924 by Richard Hirschmann.
* [https://www.microwaves101.com/encyclopedias/microwave-connectors Microwave connectors]
The male (plug) is a 4mm shaft that has a springy shroud so it fits snugly in the female (socket),
which is a 4mm hole.  In American equipment, when banana plugs are used in pairs (e.g., power and ground),
it is customary to place the two banana connectors 3/4" apart.  Although the 3/4" spacing is a de facto
standard in America, it is problematic in Europe, where a 3/4" double banana plug can easily be inserted
into a wall (mains) power receptacle by accident.


==N==
According to Wikipedia, the N connector was invented in the 1940s by Paul Neill of Bell Labs. 
The N connector is good to at least 10GHz.  It is seen as the input connector for Tektronix
spectrum analyzers [[1L20]], [[1L30]], [[1L40]], and [[492]].


==BSM==
[[Category:Repair issues]]
Several Tektronix products use BSM connectors, such as the [[7T11]], [[11B2]], [[3S2]], [[S-50]]. [[S-51]], and [[S-52]].
[[Category:Visual index pages]]
These look like minature BNC connectors.  They are much less common than BNC connectors.  There are two-lug variants
[[Category:Electromechanical components]]
and three-lug variants.  Tektronix used the two-lug variant.  They are also sometimes called MB connectors.
The [[067-0587-01]] uses one for TRIG OUT.
 
<gallery>
Image:7t11 bsm.jpg|BSM female on front lower right of 7T11
Image:Five bsm mb bnc.jpg|BSM to BNC adapters
Image:Bsm panel jack.jpg|BSM panel jack
</gallery>
 
==0.1" Header==
==IEC==
==Lemo S-series==
==Octal==
In some Tektronix equipment such as the [[160]] series, an octal connector is used.  The plug resembles the bottom of a
tube like a 6L6.  The socket is an octal tube socket.  The 160 power supply has octal sockets on the back, and octal cables
bring the power to the modules such as the [[161]], [[162]], [[163]], and [[360]].
==XLR==

Latest revision as of 13:38, 13 September 2023

Tektronix equipment makes use of a wide variety of connectors, most of which follow established standards, but occasionally, custom connectors were designed. This page presents a partial overview of connectors used in Tektronix equipment.

For details, please see the pages linked from the headings.

Coaxial connectors

BNC connector Tekprobe BNC connector
BNC Female
BNC Male
Tekprobe connector (socket)
Tekprobe-BNC interface
SMA connector SMB connector
SMA Male
SMA Female
SMB Connector as Strobe Input to 4S1 Sampler
SMB Connector as Tripper Pulse Input to 284 Tunnel Diode
3.5 mm connector 2.92 mm connector
3.5 mm female image needed
3.5 mm male
2.92 mm female
2.92 mm male
UHF connector N connector
UHF socket (on a Type G plug-in)
The 013-045 has one male two female UHF connectors
GR-874 connector BSM connector
GR-874 cable connector
GR-874 connector on an S-1 sampling head
BSM female on front lower right of 7T11
BSM panel jack
Gremar connector Peltola connector
Socket
Tip
TNC connector  
TNC Female
TNC Male
    

See also Coax connector comparison

Fiberoptic connectors

FC/PC connector

Non-coaxial low-voltage connectors

Banana connector LEMO S-series connector
Banana plug (original style)
Banana jack (Ext H input on 502)
LEMO S-series male (on P6201)
Probe power connector on rear panel of 7104
GPIB connector Amphenol 165 series connectors
GPIB connector on back of a Tektronix TDS210 scope
Stacking GPIB cable connector
Rear Connector on 175
Rear Connector on 575
XLR connector 0.1" header
3-pin XLR cable plug and socket
5-pin XLR panel socket
0.1" pin headers with cable connectors
D-sub connector

Power connectors

IEC connector Octal connector
IEC 320 (60320) C14 power inlet
IEC 320 (60320) C13 cable plugs
Modern octal cable plug
Octal power sockets on 160 series modules
NEMA 5-15 connector NEMA 1-15 connector
NEMA 5-15 ("Edison"), recessed
NEMA 5-15 ("Edison")
NEMA 1-15

Links

Retrieved from "https://w140.com/tekwiki/index.php?title=Connectors&oldid=84627"