P6032: Difference between revisions

P6032 (view source)

Revision as of 01:14, 31 October 2021

175 bytes added , 31 October 2021

no edit summary

Peter

Bureaucrats, Interface administrators, Suppressors, Administrators

36,479

edits

@@ Line 1: / Line 1: @@
+{{Probe Sidebar
+|manufacturer=Tektronix
+|model=P6032
+|summary=850 MHz cathode-follower probe
+|for=1S1
+|image=Tek p6032 kit 1.jpg
+|caption=P6032
+|introduced=(?)
+|discontinued=(?)
+|manuals=
+* [[Media:070-327.pdf|Tektronix P6032 Manual (PDF)]] / [http://w140.com/kurt/p6032.djvu (DjVu)]
+* [[Media:Tek_P6032_preliminary_manual_1962.pdf|Tektronix P6032 Preliminary Manual (PDF)]]
+}}
 The '''Tektronix P6032''' is an 850 MHz cathode-follower probe, intended for use with samplers such as the [[1S1]], [[3S1]], [[3S76]], [[4S1]], and [[4S2]].
 It was designed by [[Murlan Kaufman]].
@@ Line 4: / Line 17: @@
 There is an [[EC1000]] subminiature triode in the probe body, which is why it gets slightly warm during operation.
-Like all active probes, the P6032 requires power, and for this reason it has two connectors at the scope end of cable.
+Like all active probes, the P6032 requires power, and for this reason it has two connectors at the scope end of the cable.
 There is a four-pin power connector and a 50 Ω [[GR-874 connector]] for the signal.
@@ Line 15: / Line 28: @@
 {{BeginSpecs}}
-{{Spec | Bandwidth | 850 MHz }}
+{{Spec | Bandwidth | ≥850 MHz }}
 {{Spec | Rise time | 0.4 ns max. }}
 {{Spec | Attenuation |10× to 1000× in 1-2-5 steps with supplied attenuator heads, 3× without attenuator }}
-{{Spec | Dynamic range | ±0.15 V &times attenuation }}
+{{Spec | Dynamic range | ±0.15 V × attenuation }}
-{{Spec | Maximum input voltage | ±0.225 V &times attenuation, de-rated for CW operation for 500× and 1000× attenuator heads }}
+{{Spec | Maximum input voltage | ±0.225 V × attenuation, de-rated for CW operation for 500× and 1000× attenuator heads }}
 {{Spec | Input resistance | 10 MΩ with any attenuator head, 3 MΩ without attenuator head }}
 {{Spec | Input capacitance | 3.6 pF (10× head) to 1.3 pF (1000× head), 7 pF without attenuator head}}
 {{Spec | Output impedance | not specified, calibrated for 50 Ω load }}
-{{Spec | dc offset | ≈0.5 V (not adjustable)}}
+{{Spec | DC offset | ≈0.5 V (not adjustable)}}
 {{EndSpecs}}
-==Manuals==
-* [[Media:070-327.pdf|Tektronix P6032 Manual (PDF)]] / [http://w140.com/kurt/p6032.djvu (DjVu)]
-* [[Media:Tek_P6032_preliminary_manual_1962.pdf|Tektronix P6032 Preliminary Manual (PDF)]]
 ==Pictures==
 <gallery>
-P6032_ext.jpg|External view of P6032 without attenuator attachment.
+P6032_ext.jpg | External view of P6032 without attenuator attachment
-P6032-schematic.png|P6032 Schematic
+P6032-schematic.png | P6032 Schematic
-P6032_int_c.jpg|Internal view of P6032  Probe tip connects directly to triode grid, which is a bare wire coming out of the top of the tube.  Clipping line runs along the body of the probe to the left of the tube socket.
+P6032_int_c.jpg | Internal view of P6032  Probe tip connects directly to triode grid, which is a bare wire coming out of the top of the tube.  Clipping line runs along the body of the probe to the left of the tube socket.
-P6032x10.jpg |  ×20 attenuator tip
+P6032x10.jpg | ×20 attenuator tip
-P6032_pwr.jpg|Internal view of power supply at end of P6032 cable.  Signal coax passes through undisturbed.
+P6032_pwr.jpg | Internal view of power supply connector. Signal coax passes through undisturbed.
-P6032_risetime.jpg|Display on [[545|545A]] with 1S1 and P6032.  Pulse is generated by Tek [[284]] tunnel diode pulser driving into 50 ohm load, GR-BNC adaptor and then to the probe using a probe to BNC adaptor.  The 10x attenuator tip was used on the P6032.  Timebase is 200ps/div.
+P6032_risetime.jpg | Display on [[545|545A]] with 1S1 and P6032.  Pulse is generated by Tek [[284]] tunnel diode pulser driving into 50 Ω load, GR-BNC adaptor and then to the probe using a probe to BNC adaptor.  The 10x attenuator tip was used on the P6032.  Timebase is 200 ps/div.
 Tek p6032 kit 1.jpg
 Tek p6032 kit 2.jpg