S-4: Difference between revisions

Revision as of 13:17, 10 December 2023

Tektronix S-4

Sampling Head

Compatible with 7000 and 3S series sampling heads

Produced from 1968 to 1990

Manuals

(All manuals in PDF format unless noted otherwise)

Manuals – Specifications – Links – Pictures

The Tektronix S-4 is a sampling head for 7000- and 3S-series samplers. It was designed by George Frye and introduced in 1968. It is the fastest of the S-series plug-in samplers.

During the development of the S-4, the velocity gate theory was tested using a length of transmission line between diodes. This led to a aperture time that depended upon twice the propagation delay of the length of transmission line.

Key Specifications

Rise time	25 ps (observed with S-50 or S-52, 35 ps)
Bandwidth	14.5 GHz
Input impedance	50 Ω (terminated SMA connector)
Input range	1 V_p-p (operating)
Maximum input	±5 V max. non-destructive
Noise	< 5 mV
Features	trigger signal pick-off for internal triggering

Internals

The S-4 sampling gate is based upon a traveling wave trapped-charge transmission line in which the sampling window is set by the propagation time of a pulse edge through a thick-film transmission line. This technique requires only a sharp pulse edge rather than a precise pulse width, which is harder to generate. The sampling diodes are housed in a special coaxial connector that provides a high bandwidth signal path.

To disassemble the sampler hybrid, first remove it from the sampler board as per the manual. Remove the input connector using a 7/32" wrench and remove the 20 dB attenuator with small pliers. The ceramic board is held to the housing using roll pins that can be pressed out with a 0.030" pin punch. The hybrid has six diodes, each about 0.75mm square. The cathodes are glued to the gold substrate with conductive epoxy and the anodes are wire-bonded (twice) over a gap to the next step in the strobe line. It appears that a standard beam-lead diode may fit across the gap but cleanly removing a failed diode without damaging the substrate would be quite difficult.

Prices

1979: $1,435 (~$5,600 in 2022 Dollars)

According to an internal memo, in 1979 annual sales were estimated at 150 units.

Links

Pictures

Top view of the S4 plug-in
Left view
Right view
Schematic
Sampler board, strobe side
Sampler board, preamp side
Sampler board, disassembled with parts orientation
Microphotograph of sampler hybrid
S-4 B-prototype, no difference to standard S-4
S-4 in 7S11
S-4 in 7S11

Parts

Some Parts Used in the S-4

Part	Part Number(s)	Class	Description	Used in
152-0335-00	152-0335-00	Discrete component	step recovery diode	S-4 • S-6
152-0335-01	152-0335-01	Discrete component	150 ps step recovery diode	1502 • S-2 • S-4 • S-6
155-0001-00	155-0001-00	Hybrid integrated circuit	gate assembly	S-4

@@ Line 10: / Line 10: @@
 |designers=George Frye
 |manuals=
-* [[Media:070-0896-01.pdf|Tektronix S-4 Instruction Manual, Revised OCT 1986]] (OCR)
+* [[Media:070-0896-00.pdf|Tektronix S-4 Manual 1969]] (OCR)
-* [[Media:070-0896-00.pdf|Tektronix S-4 Manual 1969]]
+* [[Media:070-0896-01 march 1985.pdf|Tektronix S-4 Instruction Manual, Revised March 1985]] (OCR)
-* [http://w140.com/tek_S4_1985.pdf Tektronix S-4 Manual, revised 1985]
+* [[Media:070-0896-01.pdf|Tektronix S-4 Instruction Manual, Revised October 1986]] (OCR)
 * [[Media:Frye s4 gate.pdf|George Frye's Explanation of S-4 sampler in October 1968 Service Scope]]
 * [[Media:Tek s-4 fcp april 1969 - OCR.pdf|Tektronix S-4 Factory Calibration Procedure, April 1969]] (OCR)