36,756
edits
mNo edit summary |
No edit summary |
||
Line 1: | Line 1: | ||
{{Oscilloscope Sidebar | | {{Oscilloscope Sidebar | ||
|manufacturer=Tektronix | |||
|series=5000-series scopes | |||
|model=5110 Mod 709V for Bently Nevada | |||
|summary=5110 modified for radial vibration display | |||
|image=Bently-nevada-5110-mod-709v-4-crop.jpg | |||
|caption=5110 Mod 709V for Bently Nevada | |||
|introduced=(?) | |||
|discontinued=(?) | |||
|manuals=See main text | |||
}} | }} | ||
Mod 709V appears to be an adaptation of [[5110]] scopes for radial vibration display made by Tektronix in Beaverton for [https://en.wikipedia.org/wiki/Bently_Nevada Bently Nevada] and possibly others. | Mod 709V appears to be an adaptation of [[5110]] scopes for radial vibration display made by Tektronix in Beaverton for [https://en.wikipedia.org/wiki/Bently_Nevada Bently Nevada] and possibly others. | ||
Line 52: | Line 53: | ||
'''DESCRIPTION''' | '''DESCRIPTION''' | ||
This manual describes MOD 709V as it applies to the | This manual describes MOD 709V as it applies to the TEKTRONIX 5110 Single Beam Oscilloscope. MOD 709V adds a new circuit board for X-Y operation using Right Vertical versus Left Vertical. | ||
TEKTRONIX 5110 Single Beam Oscilloscope. MOD 709V | Using a TEKTRONIX 5B10N MOD 709V Time Base plug-in unit, the SECONDS/DIV or VOLTS/DIV switch is turned to the L versus R position actuating a switching relay mounted in the mainframe. | ||
adds a new circuit board for X-Y operation using Right | This bypasses the normal sweep function of the 5B10N, allowing for a Left Vertical versus Right Vertical X-Y display. | ||
Vertical versus Left Vertical. Using a TEKTRONIX 5B10N | The display unit portion of the 5110 is supplied with an illuminated graticule with a special implosion shield, and an AC coupled EXT INTENSITY INPUT via a yellow binding post at the front panel. | ||
MOD 709V Time Base plug-in unit, the SECONDS/DIV or | |||
VOLTS/DIV switch is turned to the L versus R position | |||
actuating a switching relay mounted in the mainframe. This | |||
bypasses the normal sweep function of the 5B10N, allowing | |||
for a Left Vertical versus Right Vertical X-Y display. The | |||
display unit portion of the 5110 is supplied with an | |||
illuminated graticule with a special implosion shield, and an | |||
AC coupled EXT INTENSITY INPUT via a yellow binding post | |||
at the front panel. | |||
'''BANDWIDTH''' | '''BANDWIDTH''' | ||
Maximum horizontal deflection bandwidth | Maximum horizontal deflection bandwidth (using a 5A15N or 5A18N amplifier) is reduced by approximately 300 kHz by the added wiring. Bandwidth (−3 dB) for X-axis deflection from either the center or right compartment is 1.7 MHz minimum. | ||
(using a 5A15N or 5A18N amplifier) is reduced by | The Y-axis specification is unchanged. | ||
approximately 300 kHz by the added wiring. Bandwidth ( | |||
for X-axis deflection from either the center or right compartment | |||
is 1.7 MHz minimum. The Y-axis specification is unchanged. | |||
'''CALIBRATION''' | '''CALIBRATION''' | ||
Check the interconnecting wiring to the added X-Y circuit board, | Check the interconnecting wiring to the added X-Y circuit board, then calibrate MOD 709V according to the procedure in the 5110 Instruction Manual. | ||
then calibrate MOD 709V according to the procedure in the 5110 | |||
Instruction Manual. | |||
</blockquote> | </blockquote> | ||
Line 86: | Line 73: | ||
'''DESCRIPTION''' | '''DESCRIPTION''' | ||
This manual insert describes the features of MOD 709V as installed in the 5A19N | This manual insert describes the features of MOD 709V as installed in the 5A19N Differential Amplifier. | ||
Differential Amplifier. The Signal Input connector has been changed to a blue | The Signal Input connector has been changed to a blue binding post for the Minus Input. The Variable VOLTS/DIV control labeled CAL has been removed. | ||
binding post for the Minus Input. The Variable VOLTS/DIV control labeled CAL | A +15 Volts offset, regardless of the VOLTS/DIV control setting has been added. | ||
has been removed. A +15 Volts offset, regardless of the VOLTS/DIV control | |||
setting has been added | |||
'''CALIBRATION''' | '''CALIBRATION''' | ||
Line 115: | Line 99: | ||
'''DESCRIPTION''' | '''DESCRIPTION''' | ||
This manual insert describes the features of MOD 709V as installed in the 5B10N | This manual insert describes the features of MOD 709V as installed in the 5B10N Time Base Amplifier. | ||
Time Base Amplifier. It removes the VAR control, changes the BNC EXT INPUT | It removes the VAR control, changes the BNC EXT INPUT connector to a green binding post and provides a switching mode for Left Vertical vs Right Vertical, The last ccw position of the SECONDS/DIV or VOLTS/DIV (EXT) switch is now labeled L vs R. | ||
connector to a green binding post and provides a switching mode for | |||
Left Vertical vs Right Vertical, The last ccw position of the SECONDS/DIV or | |||
VOLTS/DIV (EXT) switch is now labeled L vs R. | |||