2714: Difference between revisions

Jump to navigation Jump to search

2714 (view source)

Revision as of 03:11, 11 September 2023

903 bytes removed ,  11 September 2023
simplified
No edit summary
(simplified)
Line 16: Line 16:
* Service manual needed [[Category:Manual needed]]
* Service manual needed [[Category:Manual needed]]
}}
}}
The '''Tektronix 2714''' is a CATV spectrum analyzer with a frequency range of 9 kHz to 1.8 GHz.  The minimum resolution bandwidth is 300 Hz, and provides measurement resolution proportional to the frequency accuracy or span.  With non-volatile memory (NVRAM) at 124 kB can save up to 108 displays of waveforms and markers, and up to 36 front panel setups, large user-defined key programs, and antenna factor tables.
The '''Tektronix 2714''' is a CATV spectrum analyzer with a frequency range of 9 kHz to 1.8 GHz.  


The single and delta markers provide direct readout of frequency and amplitude information of any point along any displayed trace.  Or, get the relative (delta) frequency and amplitude information between any two points along any displayed trace or between traces.
The 2714 Cable TV Spectrum Analyzer supports CATV-specific functions like automatic positioning of visual aural carriers, visual and aural carrier levels and frequencies for selected channels, survey of system visual and aural carrier levels and frequencies, depth of modulation, aural carrier deviation measurement, visual carrier-to-noise measurement, and visual to carrier amplitude and frequency difference measurements.
 
The 2714 Cable TV Spectrum Analyzer has features to support the measurements necessary to maintain a functional CATV system like: Automatic positioning of visual aural carriers, Visual and aural carrier levels and frequencies for selected channels, Survey of system visual and aural carrier levels and frequencies, Depth of modulation, Aural carrier deviation measurement, Visual carrier-to-noise measurement, and Visual to carrier amplitude and frequency difference measurements.
 
Additional features include Digital Storage Display (selectable acquisition modes of positive peak only, positive/negative peak, Max hold, Waterfall, and an analog sweep when digital storage is off), Ensemble Averaging, Internal Preamp, Internal Calibrator (accessed through Input Menu), Alternate Reference Level Units (dBm, dBmV, dBV, dBµV, dBµW, and dBµV/m), User-Definable Power-on Status, Center Measure, Graticule Illumination (for CRT photography), and Direct Plot/Print (Printers via Opt. 03 GPIB, or RS-232-C interface via Opt. 08).
 
Front panel inputs/outputs are: RF INPUT [[BNC connector]] (75Ω, +20 dBm Max, 100 V DC blocking capacitor); and OPTION [[Unknown connector]] (Service manual only indicates that the front panel position is for a '''Future Option'''.  No internal tracking generators were available like with the other 2710, 2711, and 2712).
 
Rear panel inputs/outputs are: J101 [[SMA connector]] (Female SMA installed for Opt. 15), J102 EXT TRIG [[BNC connector]] (10 kΩ, 50V (DC + peak AC)), J103 [[DB9 connector]] Female (Not RS-232 compatible.  Accessory connector: Pin 1 Video Input, Pin 2 Ground, Pin 3 Video Output, Pin 6 Sweep Gate, Pin 7 Sweep Output, all others unused), J104 Opt. 03: [[GPIB connector]] (IEEE Std 488 connector) or Opt. 08: [[RS-232 interface]] (Digital Communication Port.).


{{BeginSpecs}}
{{BeginSpecs}}
{{Spec | Frequency | 9 kHz to 1.8 GHz; Preamp limited to 600 MHz }}
{{Spec | Frequency | 9 kHz to 1.8 GHz; Preamp limited to 600 MHz }}
{{Spec | Frequency Span  | 1 kHz/div to 100 MHz/div in 1, 2, 5 sequence (plus 0 Hz and MAX: 180 MHz/div) }}
{{Spec | Frequency Span  | 1 kHz/div to 100 MHz/div in 1, 2, 5 sequence (plus 0 Hz and MAX: 180 MHz/div) }}
{{Spec | Resolution Bandwidth | -6 dB bandwidth selections are 300 Hz, 1 kHz, 3 kHz, 10 kHz, 30 kHz, 100 kHz, 300 kHz, 1 MHz and 5 MHz }}
{{Spec | Resolution Bandwidth | –6 dB bandwidth selections are 300 Hz, 1 kHz, 3 kHz, 10 kHz, 30 kHz, 100 kHz, 300 kHz, 1 MHz and 5 MHz }}
{{Spec | RF Input impedance | 75 Ω }}
{{Spec | RF Input impedance | 75 Ω }}
{{Spec | Maximum Safe Input Power | +70 dBmV (0.1 W or 2.2 V) continuous peak, ≤100 V DC blocking capacitor }}
{{Spec | Maximum Safe Input Power | +70 dBmV (0.1 W or 2.2 V) continuous peak, ≤100 V DC blocking capacitor }}
{{Spec | RF Attenuator | 0 dB to 50 dB, 2 dB steps }}
{{Spec | RF Attenuator | 0 dB to 50 dB, 2 dB steps }}
{{Spec | Sensitivity (at 300 Hz RBW) | -78 dBmV (-127 dBm); -90 dBmV (-139 dBm) with preamp on }}
{{Spec | Sensitivity | (at 300 Hz RBW) -78 dBmV (-127 dBm); -90 dBmV (-139 dBm) with preamp on }}
{{Spec | Reference Level | -70 dBm to +20 dBm; -23 dBmV to +66.9 dBmV }}
{{Spec | Reference Level | -70 dBm to +20 dBm; -23 dBmV to +66.9 dBmV }}
{{Spec | Sweep Speed | 2 sec/Div to 1 µs/Div in 1, 2, 5 sequence }}
{{Spec | Sweep Speed | 2 sec/Div to 1 µs/Div in 1, 2, 5 sequence }}
Line 43: Line 35:
{{Spec | Dynamic Range | ≥100 dBm }}
{{Spec | Dynamic Range | ≥100 dBm }}
{{Spec | Internal Calibrator | 100 MHz marker at +18.8 dBmV (-30 dBm) }}
{{Spec | Internal Calibrator | 100 MHz marker at +18.8 dBmV (-30 dBm) }}
{{Spec | Included Accessories | PC Software; Power Cord; User Manual; Programmer Manual; Software Reference Manual; Front Cover; 75Ω BNC Connector, 75Ω F Connector; Choice of GPIB or RS-232 (Opt. 03 or Opt. 08)}}
{{Spec | Power | 90 − 132 V<sub>AC</sub>, 48 to 440 Hz; 90 – 250 V<sub>AC</sub>, 48 to 63 Hz.  At 115 V<sub>AC</sub>, 60 Hz, 90 W (standard), 105 W max (with options) }}
{{Spec | Power | 90 − 132 V<sub>AC</sub>, 48 to 440 Hz; 90 – 250 V<sub>AC</sub>, 48 to 63 Hz.  At 115 V<sub>AC</sub>, 60 Hz, 90 W (standard), 105 W max (with options) }}
{{Spec|Features|
* 124 kB NVRAM to save up to 108 waveform displays, 36 front panel setups, -defined key programs, and antenna factor tables.
* Single and delta markers – readout of frequency and amplitude
* Digital storage display
* Acquisition modes: positive peak only, positive/negative peak, Max hold, Waterfall, an analog sweep (when digital storage is off)
* Ensemble averaging
* Internal preamp
* Internal Calibrator
* Alternate reference level units (dBm, dBmV, dBV, dBµV, dBµW, and dBµV/m)
* Direct plot/print (Printers via Opt. 03 GPIB, or RS-232-C interface via Opt. 08).
}}
{{EndSpecs}}
{{EndSpecs}}
Front panel:
* RF INPUT [[BNC connector]] (75 Ω, +20 dBm max, 100 V DC blocking capacitor
* OPTION [[Unknown connector]] (Service manual only indicates that the front panel position is for a '''Future Option'''.  No internal tracking generators were available like with the other 2710, 2711, and 2712).
Rear panel:
* J101 [[SMA connector]] (for Opt. 15)
* J102 EXT TRIG [[BNC connector]] (10 kΩ, 50 V (DC + peak AC))
* J103 [[DB9 connector|DB-9 female]] Accessory connector: Pin 1 Video Input, Pin 2 Ground, Pin 3 Video Output, Pin 6 Sweep Gate, Pin 7 Sweep Output, all others unused)
* J104 Opt. 03: [[GPIB connector]] or Opt. 08: [[RS-232 interface]] (Digital Communication Port.).


==Options==
==Options==
Retrieved from "https://w140.com/tekwiki/wiki/Special:MobileDiff/84590"

Navigation menu