585: Difference between revisions
No edit summary |
No edit summary |
||
Line 6: | Line 6: | ||
primarily in the impedance of the signal interface between the plug-in and the scope. | primarily in the impedance of the signal interface between the plug-in and the scope. | ||
The [[81|Type 81]] adapter allows the use of letter-series and 1-series plug-ins in a 585. | The [[81|Type 81]] adapter allows the use of letter-series and 1-series plug-ins in a 585. | ||
The original 585 has a | |||
[[tunnel diodes|tunnel diode]] | The original 585 (up to serial number 1070) has an "A" trigger circuit that has a differential | ||
trigger amplifier made of a pair of [[6EW6]] nuvistors, followed by a Schmitt trigger | |||
Unlike other 500-series scopes, the 585 CRT, | made of a pair of [[6DJ8]] tubes. Starting at serial number 1071, the 6DJ8 Schmitt trigger | ||
the [[T581]] | was replaced by 10mA [[tunnel diodes|tunnel diode]] and a pulse amplifier made with an OC171 germanium PNP | ||
transistor. The tunnel diode is AC-coupled to the base-emitter junction of the transistor. | |||
Like the [[545]], [[551]], and [[555]], the 585 uses a [[distributed amplifier]] for vertical deflection. | |||
Unlike the other 500-series scopes, the 585 uses a CRT, | |||
with distributed vertical deflection plates, the [[T581]], | |||
enabling it to have both high sensitivity and fast risetime. | enabling it to have both high sensitivity and fast risetime. | ||
The total CRT acceleration voltage is 10kV. | The total CRT acceleration voltage is 10kV. | ||
Several improvements were published for the 585 circuitry, including the enhanced trigger | Several improvements were published for the 585 circuitry, including the enhanced trigger | ||
circuit. If all of those changes are applied to a 585, it is essentially a 585A. | circuit. If all of those changes are applied to a 585, it is essentially a 585A. | ||
A rackmount version was also made. | A rackmount version was also made. |
Revision as of 12:55, 27 November 2011
The Type 585 is a 100MHz 580-Series scope introduced by Tektronix in 1959 and made through the 1960's. The 585 uses 580-series plug-ins, which look like letter-series and 1-series plug-ins but are electrically different, primarily in the impedance of the signal interface between the plug-in and the scope. The Type 81 adapter allows the use of letter-series and 1-series plug-ins in a 585.
The original 585 (up to serial number 1070) has an "A" trigger circuit that has a differential trigger amplifier made of a pair of 6EW6 nuvistors, followed by a Schmitt trigger made of a pair of 6DJ8 tubes. Starting at serial number 1071, the 6DJ8 Schmitt trigger was replaced by 10mA tunnel diode and a pulse amplifier made with an OC171 germanium PNP transistor. The tunnel diode is AC-coupled to the base-emitter junction of the transistor.
Like the 545, 551, and 555, the 585 uses a distributed amplifier for vertical deflection. Unlike the other 500-series scopes, the 585 uses a CRT, with distributed vertical deflection plates, the T581, enabling it to have both high sensitivity and fast risetime. The total CRT acceleration voltage is 10kV.
Several improvements were published for the 585 circuitry, including the enhanced trigger circuit. If all of those changes are applied to a 585, it is essentially a 585A.
A rackmount version was also made.
-
Front view.
-
585A trigger circuit.
-
White plastic clip holds tunnel diode for triggering.
-
Inside view shows regulator tubes.
-
Distributed vertical amplifier.
-
RM-585A