S-4: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 15: Line 15:
* [[Media:Frye s4 gate.pdf|George Frye's Explanation of S-4 sampler in October 1968 Service Scope]]
* [[Media:Frye s4 gate.pdf|George Frye's Explanation of S-4 sampler in October 1968 Service Scope]]
* [[Media:Tek s-4 fcp april 1969 - OCR.pdf|Tektronix S-4 Factory Calibration Procedure, April 1969]] (OCR)
* [[Media:Tek s-4 fcp april 1969 - OCR.pdf|Tektronix S-4 Factory Calibration Procedure, April 1969]] (OCR)
* [[Media:Tek s-4 eis signatures page.pdf|Tektronix S-4 Engineering Instrument Specification signatures page]]
}}
}}
The '''Tektronix S-4''' is a sampling head for 7000- and 3S-series samplers.
The '''Tektronix S-4''' is a sampling head for 7000- and 3S-series samplers.

Revision as of 06:30, 19 June 2024

Manuals – Specifications – Links – Pictures

The Tektronix S-4 is a sampling head for 7000- and 3S-series samplers. It was designed by George Frye and introduced in 1968. It is the fastest of the S-series plug-in samplers.

Key Specifications

Rise time 25 ps (35 ps observed with S-50 or S-52)
Bandwidth 14.5 GHz
Input impedance 50 Ω (terminated SMA connector)
Input voltage 1 Vp-p (operating)
Maximum input ±5 V max. non-destructive
Noise < 5 mV
Features
  • trigger signal pick-off for internal triggering

Internals

The S-4 sampling gate is based upon a traveling wave trapped-charge transmission line in which the sampling window is set by the propagation time of a pulse edge through a thick-film transmission line. This technique requires only a sharp pulse edge rather than a precise pulse width, which is harder to generate. The sampling diodes are housed in a special coaxial connector that provides a high bandwidth signal path.

During the development of the S-4, the velocity gate theory was tested using a length of transmission line between diodes. This led to an aperture time that depended upon twice the propagation delay of the length of transmission line.

To disassemble the sampler hybrid, first remove it from the sampler board as per the manual. Remove the input connector using a 7/32" wrench and remove the 20 dB attenuator with small pliers. The ceramic board is held to the housing using roll pins that can be pressed out with a 0.030" pin punch.

The hybrid has six diodes, each about 0.75 mm². The cathodes are glued to the gold substrate with conductive epoxy and the anodes are wire-bonded (twice) over a gap to the next step in the strobe line. It appears that a standard beam-lead diode may fit across the gap but cleanly removing a failed diode without damaging the substrate would be quite difficult.

Prices

1979: $1,435 (~$6,000 in 2023 dollars)

According to an internal memo, annual sales were estimated at 150 units in 1979.

Links

Patents that may apply to S-4

Page Title Inventors Filing date Grant date Links
Patent US 3629731A Sampling system George Frye 1968-07-12 1971-12-21

Pictures

Parts

Some Parts Used in the S-4

Part Part Number(s) Class Description Used in
152-0335-00 152-0335-00 Discrete component step recovery diode S-4 S-6
152-0335-01 152-0335-01 Discrete component 150 ps step recovery diode 1502 S-2 S-4 S-6
155-0001-00 155-0001-00 Hybrid integrated circuit gate assembly S-4