7104

Manuals – Specifications – Links – Pictures

The Tektronix 7104 is a 1 GHz, non-storage 7000-series oscilloscope mainframe that takes two 7000-series vertical plug-ins and two 7000-series horizontal plug-ins. It was introduced in 1978. There is also a rack-mount version, the R7103, albeit with only one horizontal bay.

The scope employs a micro-channel plate (MCP) CRT design to get good screen intensity at high sweep speeds with moderate acceleration voltage.

The high speed necessitated using distributed deflection plates also for the horizontal deflection system, which reaches a bandwidth of 350 MHz. Option 2 adds a horizontal delay line to make the high horizontal bandwidth available for X-Y mode at a phase shift of <2° up to 50 MHz, nullable at any frequency up to 250 MHz.

The 7A29 1 GHz vertical amplifier and the 7B15/7B10 time base pair were introduced along with the 7104 to match the system bandwidth.

Key Specifications

Bandwidth	1 GHz (with 7A29) – rise time < 350 ps
Fastest calibrated sweep	200 ps/Div (with 7B10)
Calibrator	40 mV to 4 V (p-p) in decade steps, 1 kHz; 4 mV to 400 mV into 50 Ω; 40 mA with adapter
Y delay line	51 ns (frequency compensated coax pair)
X-Y phase shift	base model: < 2° from DC to 50 kHz Opt. 2: < 2° from DC to 50 MHz (with a pair of 7A19 or 7A29, at least one of which has the variable delay option)
Acceleration voltage	12.5 kV
CRT	T7100-31-2 Micro channel plate CRT (154-0783-00), P31 phosphor, 8 × 10 Div. @ 8.5 mm, resolution 17 lines / Div., vertical 2 GHz bandwidth @ 1 V/Div sensitivity
Power consumption	215 W
Dimensions	345 mm (h) × 305 mm (w) × 592 mm (l)
Weight	19.8 kg (43.6 lb)
Features	Readout 2 probe power connectors

MCP protection

The Micro Channel Plate's amplification degrades irreversibly with operation, in proportion to the log of total charge passed per channel or display area. For this reason, continued operation with a steady trace and especially at large beam currents must be avoided. The 7104 contains a "limited viewing time" circuit to assist with observing this restriction. At beam currents above 0.2 μA, a yellow indicator illuminates, and the beam will be shut down after 20 minutes. The limit time drops to two minutes at an average beam current of 2 μA, and also limits the average current to that value. Single-shot display current is not affected. Despite this limiter, older instruments often exhibit darkening of the screen around the horizontal center line to some degree (see screen shot).

Internals

The 7104 makes extensive use of custom integrated circuits and hybrid circuits, inter alia, the 155-0174-00 Delay Line Compensator, 155-0173-00 Vertical Channel Switch, 155-0176-00 Vertical Output Amplifier, 155-0194-00/01/02/03 CRT Termination, 155-0175-00 Trigger Amplifier, 155-0178-00 Horizontal Output Amplifier, 155-0012-00 Z-Axis controller/amplifier, and 155-0067-02 SMPS controller. The high-speed amplifiers use Hypcon ceramic packages that use elastomer-based frames for coupling chip connections to the circuit board at constant impedance. The signal connections are differential throughout, and the signal path was optimized for matching and low reflection, including the plugin to mainframe card-edge connectors and the use of stripline and coplanar waveguide techniques right up to the CRT.

The 7104's amplifiers use a then novel scheme of "feed-beside" compensation (US Pat. 4.132.958) where instead of matching the HF response to the LF response, the LF response is determined by off-the-shelf operational amplifiers in parallel to the high-speed amplifiers, with a number of adjustable R-C time constants to compensate for thermal and other LF effects. The same technique is employed in the 7A29 amplifier plug-in.

Prices

	Year	1980	1984	1990
Mainframe only	Catalog price	$14,400	$21,380	$29,995
	2015 value	$41,560	$48,930	$54,580
Mainframe with 7A29, 7A29 Opt. 04, 7B15, 7B10	Catalog price	$21,730	$31,875	$44,510
	2015 value	$62,700	$72,960	$88,990

Links

• Hans Springer: 1 GHz at 10 mV in a General Purpose Plug-in Oscilloscope. In TekScope Vol. 11 No. 1, 1979
• Hans Springer's 1979 Electronic Design article on the 7104
• Reading Jim Williams: Scope Sunday 4
• Tek 7104 @ amplifier.cd
• Tek 7104 @ barrytech.com
• A Tektronix oscilloscope that moved faster than light? The Oregonian, 23 Sep 2011. (Original no longer accessible, link via archive.org.)
• Tektronix 7104 @ radiomuseum.org

Pictures

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 

  7104 horizontal (top) and vertical (bottom) output amplifiers

• 

  7104 horizontal output amplifier, CRT connection and termination of distributed horizontal deflection plates

• 

  7104 vertical channel switch board

• 

Measurements

• 

  Rise time measurement. 150 ps risetime pulse from 067-0587-02 at 100 Hz repetition rate. Measured 240 ps (corrected for 150 ps fixture rise time: 190 ps = 1.8 GHz)

• 

  Rise time measurement as before, 1000 Hz repetition rate at same brightness settings.

• 

  7104 recording a single shot pulse (from 067-0587-02) at 200 ps/Div. Camera: Nikon D7000, 50 mm f/1.4, ISO 3200, 1/2 s. CRT filter not removed.

• 

  7104 recording 1 GHz sine, single shot at 200 ps/Div. Camera: Nikon D7000, 50 mm f/1.4, ISO 3200, 1/2 s. CRT filter not removed. CRT amplification loss is evident around the center line.

• 

  Faster-than-light beam on 7104? Using a 067-0587-02 calibration fixture at maximum amplitude produces this trace spanning 1.2 Div horizontally at 200 ps/Div and 8 Div vertically. Trace length is (1.2² + 8²)^½ × 8.5 mm = 68.8 mm, travelled in 1.2 × 200 ps = 240 ps. Apparent speed is therefore 68.8×10^-3 / 240×10^-12 m/s or 2.86×10⁸ m/s. 95.6% c₀ - a very near miss ...