7A29: Difference between revisions
No edit summary |
No edit summary |
||
| Line 23: | Line 23: | ||
{{Spec | Deflection | 10 mV/div to 1 V/div, 1-2-5, ±2%; variable 2.5:1 }} | {{Spec | Deflection | 10 mV/div to 1 V/div, 1-2-5, ±2%; variable 2.5:1 }} | ||
{{Spec | Channels | Single channel }} | {{Spec | Channels | Single channel }} | ||
{{Spec | Recommended probes | [[P6056]] (×10), [[P6057]] (×100) }} | |||
{{Spec | Options | Option 4: variable delay (1 ns) }} | {{Spec | Options | Option 4: variable delay (1 ns) }} | ||
{{EndSpecs}} | {{EndSpecs}} | ||
| Line 52: | Line 53: | ||
File:7a29 input amp schem.png| input amplifier schematic | File:7a29 input amp schem.png| input amplifier schematic | ||
File:7a29 output amp schem.png| output amplifier schematic | File:7a29 output amp schem.png| output amplifier schematic | ||
</gallery> | |||
==Measurements== | |||
<gallery> | |||
File:7a29-rise.jpg | Sample 7A29 rise time measurement (Source: [[S-52]]) - 320 ps equiv. 1.09 GHz system bandwidth including [[7104]] mainframe | |||
</gallery> | </gallery> | ||
[[Category:7000 series vertical plugins]] | [[Category:7000 series vertical plugins]] | ||
Revision as of 01:55, 9 October 2015
Template:Plugin Sidebar 2 The Tektronix 7A29 is a 1 GHz single-channel vertical plug-in for 7000-series scopes. It is primarily intended for the 7103 and 7104. Like with the 7A19, a variable signal delay was available as an option.
There is also a 7A29P, which has digitally programmable gain, intended for the 7000 series digitizers.
The 7F10 uses the 7A29's amplifier board after the optical/electrical converter.
Key Specifications
| Bandwidth | 1 GHz (in 7104) |
|---|---|
| Input impedance | 50±1 Ω, VSWR <1.2:1 from DC to 1 GHz (10 mV/Div: 1.4:1, Opt.4: 1.5:1) |
| Max. input | max. 10 VRMS or 1 Ws pulses not exceeding 50 V; max. 100 V additional DC component in AC mode |
| Deflection | 10 mV/div to 1 V/div, 1-2-5, ±2%; variable 2.5:1 |
| Channels | Single channel |
| Recommended probes | P6056 (×10), P6057 (×100) |
| Options | Option 4: variable delay (1 ns) |
Internals
The 7A29 employs a number of Tek-made custom Hypcon-packaged hybrids, the 155-0180-00 fast input protection, 155-0181-00 input amplifier and 155-0175-00 trigger amplifier (2 ×).
It uses a "feed-beside" scheme implemented with standard low-frequency operational amplifiers to compensate for low-frequency anomalies in the frequency response that are attributed to transistor heating.
The input connector is a special Tek-made part that is exactly 50 Ω. Typical BNC connectors are around 52 Ω.
Links
Pictures
-
7A29 Opt.4 front
-
7A29 Opt.4, left view (variable delay line enclosure above PCB)
-
7A29 amplifiers
-
7A29, right side, rear
-
7A29, right side, front
-
7A29P
-
photo of 7A29 from manual (normal and option 4 units)
-
input amplifier schematic
-
output amplifier schematic
