7D13: Difference between revisions

Revision as of 04:09, 29 December 2021

Tektronix 7D13
3½ digit Digital Multimeter 7D13 front view Compatible with 7000-series scopes Produced from 1971 to 1987 Manuals Tektronix 7D13 Service (OCR) 7000 Series Digital Plug-In Applications (All manuals in PDF format unless noted otherwise)

Manuals – Specifications – Links – Pictures

The Tektronix 7D13 is a digital multimeter plug-in for 7000-series scopes with CRT readout. It will function in any compartment. The 7D13 was introduced in 1971 and followed by the 7D13A face-lift in 1982.

There is no analog output signal presented on the CRT, therefore it is not necessary to select the 7D13 with the oscilloscope Vertical or Horizontal Mode switches.

The input section is galvanically isolated, allowing the input to float ±1500 volts with respect to chassis ground.

Key Specifications

Functions	DC Volts, DC Current, Resistance, Temperature
Voltage Ranges	1.999 V, 19.99 V, 199.9 V, 1000 V (max. 500 V via P6058)
Input impedance	10 MΩ
Current ranges	1.999 mA, 19.99 mA, 199.9 mA, 1999 mA
Resistance ranges	199.9 Ω, 1999 Ω, 19.99 kΩ, 199.9 kΩ, 1999 kΩ
Temperature	7D13: −55 °C to +125 °C, requires P6058 voltage/temperature probe 7D13A: requires P6601 PT-100 probe

Internals

The 7D13 consists of an analog pulse-width modulator front-end, built with 741 op amps and dual FETs, and a 3½ digit counter section, using standard 74xx TTL parts, that interfaces with the readout system through a 155-0038-00 D/A converter. The front-end is isolated by transformers used for pulses and a floating ±15 V supply. The Probe jack for the P6058 (a 4-pin LEMO S-series connector) has contacts for the temperature sensor (a diode-connected transistor) as well as the voltage input terminals.

Links

Pictures

from manual
left
right

Custom ICs used in the 7D13

Page	Model	Part nos	Description	Designers	Used in
155-0038-01	155-0038-01	155-0038-00 • 155-0038-01	5-bit current source D/A converter	Mike Metcalf	7A42 • 7D13 • 7D14 • 7M13 • T4005

@@ Line 1: / Line 1: @@
-{{Plugin Sidebar |
+{{Plugin Sidebar
-manufacturer=Tektronix | type=7D13|
+|manufacturer=Tektronix
-summary=3½ digit Digital Multimeter|
+|series=7000-series scopes
-image=7D13_front.jpg |
+|type=7D13
-caption=7D13 front view |
+|summary=3½ digit Digital Multimeter
-introduced=1971 |
+|image=7D13_front.jpg
-discontinued=1987 |
+|caption=7D13 front view
-series=7000-series scopes|
+|introduced=1971
-manuals=
+|discontinued=1987
-* [[Media:070-1096-00.pdf|Tektronix 7D13 Service]] (OCR, PDF)
+|manuals=
-* [[Media:7000 Series Digital Plug-In Applications.pdf|7000 Series Digital Plug-In Applications (PDF)]]
+* [[Media:070-1096-00.pdf|Tektronix 7D13 Service]] (OCR)
+* [[Media:7000 Series Digital Plug-In Applications.pdf|7000 Series Digital Plug-In Applications]]
 }}
-The '''Tektronix 7D13''' is a digital multimeter plug-in for [[7000-series scopes]] with CRT readout. It will function in any compartment. There is no analog output signal presented on the CRT; therefore, it is not necessary to select the 7D13 with the oscilloscope Vertical or Horizontal Mode switches.
+The '''Tektronix 7D13''' is a digital multimeter plug-in for [[7000-series scopes]] with CRT readout. It will function in any compartment.  The 7D13 was [[introduced in 1971]] and followed by the [[7D13A]] face-lift in 1982.
+There is no analog output signal presented on the CRT, therefore it is not necessary to select the 7D13 with the oscilloscope Vertical or Horizontal Mode switches.
 The input section is galvanically isolated, allowing the input to float ±1500 volts with respect to chassis ground.
@@ Line 21: / Line 24: @@
 {{Spec | Current ranges     | 1.999 mA, 19.99 mA, 199.9 mA, 1999 mA}}
 {{Spec | Resistance ranges  | 199.9 Ω, 1999 Ω, 19.99 kΩ, 199.9 kΩ, 1999 kΩ}}
-{{Spec | Temperature        | 7D13: -55 °C to +125 °C, requires [[P6058]] voltage/temperature probe <br />7D13A: requires [[P6601]] PT-100 probe}}
+{{Spec | Temperature        | 7D13: −55 °C to +125 °C, requires [[P6058]] voltage/temperature probe <br />7D13A: requires [[P6601]] PT-100 probe}}
 {{EndSpecs}}
 ==Internals==
-The 7D13 consists of an analog pulse width modulator front-end built with 741 op amps and dual FETs, and a 3½ digit counter section using standard 74xx TTL parts which is interfacing with the [[7000 series readout system|readout system]] (through a [[155-0038-00]] D/A converter).  The front end is isolated by transformers used for pulses and a floating ±15 V supply.
+The 7D13 consists of an analog pulse-width modulator front-end, built with 741 op amps and dual FETs, and a 3½ digit counter section, using standard 74xx TTL parts, that interfaces with the [[7000 series readout system|readout system]] through a [[155-0038-00]] D/A converter.  The front-end is isolated by transformers used for pulses and a floating ±15 V supply.
 The Probe jack for the [[P6058]] (a 4-pin [[LEMO S-series connector]]) has contacts for the temperature sensor (a diode-connected transistor) as well as the voltage input terminals.