11A32: Difference between revisions

Revision as of 20:33, 31 December 2022

Tektronix 11A32
400 MHz dual channel vertical plug-in Tektronix 11A32 Compatible with 11000-series scopes Produced from 1987 to (?) Manuals 11A32 Manual 11A32 Service Reference 11A32 Extended Service Manual (OCR, with schematics) Tektronix 11k Plug-in NVRAM Replacement Tektronix 11A32 Preliminary Service Manual] (All manuals in PDF format unless noted otherwise)

Manuals – Specifications – Links – Pictures

The Tektronix 11A32 is a 400 MHz dual-channel amplifier plug-in for 11000-series scopes.

Key Specifications

Bandwidth	DC to 400 MHz. 100 MHz and 20 MHz four pole BWL (Bandwidth Limit) filters may be selected.
Rise time	875 ps in 1 GHz mainframes such as the 11402, 11402A, 11403, 11403A, DSA601A, or DSA602A
Deflection	1 mV to 10 V per division in 1% calibrated steps
Input impedance	50 Ω or 1 MΩ
Features	High-resolution calibrated DC offset Fast overdrive recovery 5 V_RMS overload protection in 50 Ω mode, with manual reset

Internals

Analog

Each input channel has a separate attenuator module containing passive 1 megohm attenuators, an AC coupling capacitor, a switch selecting the calibrator or signal input, and an M474 buffer amplifier. The calibrator signal turned off inside the plugin when not in use.

The attenuator module output feeds the + input of the M377 amplifier IC through a (blue) 50 ohm transmission line, one per input channel. The cable lengths set a standard delay per plugin.

The M377's - input is connected to the ACVS (Analog Control Voltage System) output.

The (differential) display outputs of the two amplifiers are hard-wired in parallel and drive the mainframe’s 50 Ω per side input impedance. The same is true of the trigger outputs of the two amplifiers.

The version of the M377 used in the 11A32 has a 100 Ω output impedance per side so that two of them in parallel create a source impedance of 50 Ω.

Each M377 amplifier's nominal common-mode output voltage is zero whether enabled or not. When not enabled, each M377 differential output is exactly zero by design. This fact is used during calibration by the plugin’s firmware to determine the mainframe’s imbalance and compensate for it during normal operation.

Each of the two channels has its own AUX output on dedicated pins of the plug-in interface connector:

Digital

The 11A32 and the 11A34 use exactly the same firmware.

The 11A32 and 11A34 were originally intended to use Intel 8052 microcontrollers. However, during development, the firmware swelled beyond that chip's 8192-byte maximum on-chip ROM size. Doug Haines found an alternate supplier of 8051-compatible chips (OKI Semiconductor) that offered a 16Kbyte on-chip ROM, and that's what the plug-ins wound up with. The finished code size wound up at about 14 KB.

The 11A32 also contains a DS1120 NVRAM and an ACVS module that generates the analog control voltages needed for gain/offset control etc.

Links

Pictures

Block diagram
11A32 Main Board Schematic
11A32 Main Interface
left side internal
right side internal

Custom ICs used in the 11A32

Page	Model	Part nos	Description	Designers	Used in
M377	M377	165-2129-03 • 165-2089-06 • 155-2089-05	amplifier	John Addis	11A16 • 11A32 • 11A33 • 11A34 • 11A52 • 2245 • 2245A • 2247 • 2247A • 2252 • TDS410 • TDS420 • TDS460 • TDS520D • TDS540D • TDS580D • TDS680C • TDS684C • TDS714L • TDS724D • TDS754D • TDS784D
M474	M474		amplifier	John Addis • Ivan John Cousins	11A32 • 11A34

@@ Line 32: / Line 32: @@
 ==Internals==
 ===Analog===
-Each input channel has a separate attenuator module containing an [[M474]] buffer amplifier.
+Each input channel has a separate attenuator module containing passive 1 megohm attenuators, an AC coupling capacitor, a switch selecting the calibrator or signal input, and an [[M474]] buffer amplifier. The calibrator signal turned off inside the plugin when not in use.
-The attenuator output feeds an [[M377]] amplifier IC, one per input channel.
-The display outputs of the two M377s are hard-wired in parallel and drive the mainframe’s
+The attenuator module output feeds the + input of the [[M377]] amplifier IC through a (blue) 50 ohm transmission line, one per input channel.  The cable lengths set a standard delay per plugin.
-Ω input impedance.  The same is true of the trigger outputs of the two amplifiers.
-The version of the M377 used in the 11A32 has 100 Ω output impedance so that two of them in parallel create a source impedance of 50 Ω.
-Each M377 amplifier's nominal common-mode output voltage is zero whether enabled or not.
-When not enabled, each M377 differential output is exactly zero by design.
+The M377's - input is connected to the [[ACVS]] (Analog Control Voltage System) output.
-This fact is used during calibration by the plugin’s firmware to determine the mainframe’s imbalance and compensate for it during normal operation.
+The (differential) display outputs of the two amplifiers are hard-wired in parallel and drive the mainframe’s
+Ω per side input impedance.  The same is true of the trigger outputs of the two amplifiers.
+The version of the M377 used in the 11A32 has a 100 Ω output impedance per side so that two of them in parallel
+create a source impedance of 50 Ω.
+Each M377 amplifier's nominal common-mode output voltage is zero whether enabled or not. When not enabled, each M377
+differential output is exactly zero by design. This fact is used during calibration by the plugin’s firmware to
+determine the mainframe’s imbalance and compensate for it during normal operation.
+Each of the two channels has its own AUX output on dedicated pins of the plug-in interface connector:
 See also the block diagram below.