5T3: Difference between revisions

Revision as of 19:05, 9 June 2023

Tektronix 5T3
Timing plugin Tek 5T3 Compatible with 661 Produced from 1965 to (?) Manuals Tektronix 5T3 Manual Tektronix 5T3 Field Training Kit (low quality, no OCR) Tektronix 5T3 Field Training Kit (high quality, OCR) Tektronix 5T3 Calibration Outline (OCR) (All manuals in PDF format unless noted otherwise)

The Tektronix Type 5T3 is a timing plug-in for the Type 661 sampling oscilloscope. It uses TD253B tunnel diodes for triggering.

The 5T3 can be triggered from any of four different sources:

Internal trigger from the sampling plug-in, via interconnect J9.
Internal trigger from the calibrator module in the 661 mainframe. This works up to 1 GHz.
External trigger to the high-impedance BNC trigger input. This input is buffered by an 8056 Nuvistor cathode follower. This can be used for triggering on signals up to 20 MHz.
External trigger to the 50 Ω GR-874 trigger input. This input can drive either of two selectable signal paths:
- A path where the trigger signal skips the high-impedance Nuvistor input buffer but is still buffered by Q64 and Q124 (1 GHz NPN transistors, part number 151-0138-00) before the tunnel diode trigger event recognizer circuit. This path provides triggering up to 500 MHz.
- A passive low-impedance path, capacitively coupled to a tunnel diode for "UHF SYNC" mode. This works up to 5 GHz.

The 5T3 can also be set to free-run mode.

Part	Part Number(s)	Class	Description	Used in
151-0108-00	151-0108-00	Discrete component	350 MHz (minimum) NPN bipolar transistor	5T3
151-0138-00	151-0138-00	Discrete component	1 GHz (minimum) NPN bipolar transistor	5T3
1N3717	152-0381-00 • 152-0125-00	Discrete component	4.7 mA, 25 pF tunnel diode	1L40 • 1S1 • 1S2 • 11B1 • 11B2 • 11B2A • 147A • 1470 • 148 • 21A • 22A • 3B4 • 3B5 • 408 • 432 • 434 • 453 • 453A • 454 • 466 • 491 • 5T3 • 544 • RM544 • 546 • RM546 • 547 • RM547 • 556 • RM556 • 7B70 • 7B71 • 7D11
8056	154-0417-00	Vacuum Tube (Triode)	low-voltage Nuvistor triode	422 • 502 • W • 1S1 • 3A7 • 3S3 • 3T4 • 5T3 • 10A1
STD704	152-0125-00	Discrete component	4.7 mA tunnel diode	1L40 • 1S1 • 11B1 • 11B2 • 11B2A • 147 • R147 • 147A • R147A • 1470 • 148 • R148 • 148-M • 149 • R149 • 149A • R149A • 21A • 22A • 3B4 • 3B5 • 408 • 432 • 434 • 453 • 453A • 454 • 464 • 465 • 466 • 491 • 5T3 • 544 • RM544 • 546 • RM546 • 547 • RM547 • 556 • RM556 • 7B70 • 7B71 • 7D11

@@ Line 20: / Line 20: @@
 The 5T3 can be triggered from any of four different sources:
 # Internal trigger from the sampling plug-in, via interconnect J9.
-# Internal trigger from the calibrator module in the 661 mainframe.
+# Internal trigger from the calibrator module in the 661 mainframe. This works up to 1 GHz.
-# External trigger to the high-impedance BNC trigger input. This input is buffered by an [[8056]] [[nuvistor|Nuvistor]] cathode follower.
+# External trigger to the high-impedance BNC trigger input. This input is buffered by an [[8056]] [[nuvistor|Nuvistor]] cathode follower. This can be used for triggering on signals up to 20 MHz.
 # External trigger to the 50 Ω [[GR-874]] trigger input. This input can drive either of two selectable signal paths:
 #* A path where the trigger signal skips the high-impedance Nuvistor input buffer but is still buffered by Q64 and Q124 (1 GHz NPN transistors, part number [[151-0138-00]]) before the tunnel diode trigger event recognizer circuit. This path provides triggering up to 500 MHz.