11A32: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
 
(22 intermediate revisions by 3 users not shown)
Line 8: Line 8:
|introduced=1987  
|introduced=1987  
|discontinued=(?)  
|discontinued=(?)  
|designers=
|designers=Murlan Kaufman;Cliff Baker
|manuals=
|manuals=
* [[Media:070-5922-01.pdf|11A32 manual]] (PDF)
* [[Media:070-5922-01.pdf|11A32 Manual]]
* [[Media:070-6782-00.pdf|11A32 Service Reference]] (PDF)
* [[Media:070-6782-00.pdf|11A32 Service Reference]]  
* [[Media:070-7388-99.pdf|11A32 Extended Service Manual]] (PDF, OCR, with schematics)
* [[Media:070-7388-99.pdf|11A32 Extended Service Manual]] (OCR, with schematics)
* [[Media:Tektronix 11k plugin NVRAM replacement.pdf|Tektronix 11k Plug-in NVRAM Replacement (PDF)]]
* [[Media:Tektronix 11k plugin NVRAM replacement.pdf|Tektronix 11k Plug-in NVRAM Replacement]]
* [[Media:061-3381-00.pdf|Tektronix 11A32 Preliminary Service Manual (PDF)]]
* [[Media:061-3381-00.pdf|Tektronix 11A32 Preliminary Service Manual]]]
{{ROM Images}}
}}
}}
The '''Tektronix 11A32''' is a 400 MHz dual-channel amplifier plug-in for [[11000-series scopes]].
The '''Tektronix 11A32''' is a 400 MHz dual-channel amplifier plug-in for [[11000-series scopes]] and DSA600-series scopes.
Each of the attenuator modules contains an [[M474]] buffer amplifier.
Each of the attenuator modules feeds an [[M377]] amplifier IC.
The output signals of the two M377s combine at the output of the 11A32.
The fine steps between the deflection ranges are calibrated in 1% increments.
 
The 11A32 and the [[11A34]] use exactly the same firmware.
 
Each of the 11A32’s two channels has its own M377 amplifier.
The display outputs of the two amplifiers are hard wired in parallel and drive the mainframe’s 50 Ω input impedance.
The same is true of the trigger outputs of the two amplifiers.
The version of the M377 used in the 11A32 has 100 Ω output impedance so that two of them in parallel create a source impedance of 50 Ω.
 
Each M377 amplifier's nominal common-mode output voltage is zero whether enabled or not.
 
When not enabled each M377 differential output is exactly zero by design.
This fact is used during calibration by the plugin’s firmware to determine the mainframe’s imbalance and compensate for it during normal operation.
See the block diagram below.


{{BeginSpecs}}
{{BeginSpecs}}
{{Spec | Bandwidth  | DC to 400 MHz plus 100 MHz and 20 MHz BWL filters }}
{{Spec | Bandwidth  | DC to 400 MHz; selectable 100 MHz / 20 MHz 4-pole BWL (Bandwidth Limit) filter }}
{{Spec | Rise time  | 875 ps in 1 GHz mainframe such as the [[11402]], [[11402|11402A]], [[11403]], [[11403|11403A]], [[DSA600|DSA601A]], or [[DSA600|DSA602A]]}}
{{Spec | Rise time  | 875 ps in 1 GHz mainframes such as the [[11402]], [[11402|11402A]], [[11403]], [[11403|11403A]], [[DSA600|DSA601A]], or [[DSA600|DSA602A]]}}
{{Spec | Deflection | 1 mV to 10 V per division in 1% calibrated steps}}
{{Spec | Deflection | 1 mV to 10 V per division in 1% calibrated steps}}
{{Spec | Input impedance | 50 Ω or 1 MΩ }}
{{Spec | Input impedance | 50 Ω or 1 MΩ }}
{{Spec | Features |
{{Spec | Features |
* High-Resolution Calibrated DC Offset
* High-resolution calibrated DC offset
* Fast Overdrive Recovery
* Fast overdrive recovery
* 50 Ω mode: 5 V RMS overload protected with manual reset
* 5 V<sub>RMS</sub> overload protection in 50 Ω mode, with manual reset
}}
}}
{{EndSpecs}}
{{EndSpecs}}
==Links==
* [[11A-series plug-in NVRAM replacement]]
{{Documents|Link=11A32}}
{{PatentLinks|11A32}}


==Internals==
==Internals==
The 11A32 and [[11A34]] were originally intended to use [[Intel 8052]] microcontrollers.
===Analog===
However, during development, the firmware swelled beyond that chip's 8192-byte maximum on-chip ROM size.
Each input channel has a separate attenuator module, part number [[119-2000-0x]],
[[Doug Haines]] found an alternate supplier of 8051-compatible chips (OKI Semiconductor) that offered a 16Kbyte on-chip ROM,  
containing passive 1 MΩ attenuators, a 50 Ω termination resistor, an AC coupling capacitor,
and that's what the plug-ins wound up with. The finished code size wound up at about 14 KB.
a switch selecting the calibrator or signal input, and an [[M474]] buffer amplifier. 
In normal operation the calibrator signal to the attenuator is instead connected to ground.
 
The attenuator module output feeds the + input of the [[M377]] amplifier IC through a (blue) 50 Ω transmission line, one per input channel.  The cable lengths set a standard delay per plugin.
 
The M377's − input is connected to the [[ACVS]] (Analog Control Voltage System) output.
 
The (differential) display outputs of the two amplifiers are hard-wired in parallel and drive the mainframe’s
50 Ω per side input impedance.  The same is true of the trigger outputs of the two amplifiers.
 
The version of the M377 used in the 11A32 has a 100 Ω output impedance per side so that two of them in parallel create a source impedance of 50 Ω per side.
 
Each M377 amplifier's nominal common-mode output voltage is zero whether enabled or not. When not enabled, each M377 differential output is exactly zero by design. This fact is used during calibration by the plugin’s firmware to determine the mainframe’s imbalance and compensate for it during normal operation.
 
Each of the two channels has its own AUX output on dedicated pins of the plug-in interface connector:


The 11A32 also contains a DS1120 NVRAM and an [[ACVS]] sample and hold module.
{| class="wikitable" style="margin:auto"
|-
! signal name !! positive pin number !! negative pin number
|-
| AUX 1 || B38 || B37
|-
| AUX 2 || A36 || A35
|-
|}
See also the block diagram below.


==Links==
===Digital===
The 11A32 and the [[11A34]] use exactly the same firmware.
 
The [[11A34]] and 11A32 were originally intended to use [[Intel 8052]] microcontrollers.
However, during development, the firmware swelled beyond that chip's 8192-byte maximum on-chip
ROM size.  [[Doug Haines]] found an alternate supplier of 8051-compatible chips (OKI Semiconductor) that offered a 16 KByte on-chip ROM, and that's what the plug-ins wound up with. The finished code size is about 14 KB.  There are also units with the OKI M85C154 chip that has a piggyback EPROM (see photo below).
 
The 11A32 also contains a Dallas Semiconductor DS1220Y NVRAM storing last settings, calibration constants, and instrument serial number. 
The DS1220Y contains a battery with a typical life time of 20-30 years. 
 
There is also an [[ACVS]] (Analog Control Voltage System) sample and hold module on a daughter board that generates the analog voltages needed for gain and offset, including error correction
under microcontroller firmware control. 
 
The microcontroller also provides the digital signals sent to the M377 amplifier, setting one of its six fixed gains, one of its three bandwidths, turning on or off its selected output, and each output's normal or invert state.


* [[11A-series plug-in NVRAM replacement]]
Digital mainframes do waveform manipulation (addition, subtraction, multiplication, etc.). Consequently only one 11A32 output is on at a time. Analog mainframes however allow more than one channel to be on at a time.  This allows the plugin channels to be added or subtracted in the plugin.
* [http://www.barrytech.com/tektronix/tek11000/tek11a32.html Tek 11A32 @ barrytech.com]


==Pictures==
==Pictures==
Line 65: Line 90:
Tek 11a32 2.jpg
Tek 11a32 2.jpg
Tek 11a32 block diagram.png|Block diagram
Tek 11a32 block diagram.png|Block diagram
Tektronix 11A32 schematic pg 2 stitch.jpg|11A32 Main Board Schematic
Tek 11a32 input attenuators.jpg|11A32 Input Attenuators
Tek 11a32 kernel.jpg|11A32 Kernel
Tek 11a32 analog control and signal amplifiers.jpg|11A32 Analog Control and Signal Amplifiers
Tektronix 11A32 schematic pg 4.jpg|11A32 Main Interface
Tektronix 11A32 schematic pg 4.jpg|11A32 Main Interface
Tek 11a32 internal1.jpg|left side internal
Tek 11a32 internal1.jpg|left side internal
Line 71: Line 98:
</gallery>
</gallery>


{{Custom ICs|11A32}}
==Parts==
{{Parts|11A32}}


[[Category:11000 series plugins]]
[[Category:11000 series plugins]]
[[Category:Tekprobe BNC]]
[[Category:Tekprobe BNC]]

Latest revision as of 08:52, 22 September 2024

Tektronix 11A32
400 MHz dual channel vertical plug-in
Tektronix 11A32

Compatible with 11000-series scopes

Produced from 1987 to (?)

Manuals
ROM Images
File Pos. Checksum
160-4009-04 U700 3e2de25b
160-4009-08 U700 8c2d1027
(All manuals in PDF format unless noted otherwise)
Manuals – Specifications – Links – Pictures

The Tektronix 11A32 is a 400 MHz dual-channel amplifier plug-in for 11000-series scopes and DSA600-series scopes.

Key Specifications

Bandwidth DC to 400 MHz; selectable 100 MHz / 20 MHz 4-pole BWL (Bandwidth Limit) filter
Rise time 875 ps in 1 GHz mainframes such as the 11402, 11402A, 11403, 11403A, DSA601A, or DSA602A
Deflection 1 mV to 10 V per division in 1% calibrated steps
Input impedance 50 Ω or 1 MΩ
Features
  • High-resolution calibrated DC offset
  • Fast overdrive recovery
  • 5 VRMS overload protection in 50 Ω mode, with manual reset

Links

Documents Referencing 11A32

Document Class Title Authors Year Links
Electronic-Engineering-Aug-Sept-1988-Versatile-Analogue-Chip-John-Addis.pdf Article Versatile Analogue Chip for Oscilloscope Plug-ins John Addis 1988 M377 • 11A32 • 11A33 • 11A34 • 11A52 • Cascomp • Overdrive • Thermals • Gilbert multiplier • Pat Quinn • Gary Polhemus • Art Metz

Internals

Analog

Each input channel has a separate attenuator module, part number 119-2000-0x, containing passive 1 MΩ attenuators, a 50 Ω termination resistor, an AC coupling capacitor, a switch selecting the calibrator or signal input, and an M474 buffer amplifier. In normal operation the calibrator signal to the attenuator is instead connected to ground.

The attenuator module output feeds the + input of the M377 amplifier IC through a (blue) 50 Ω transmission line, one per input channel. The cable lengths set a standard delay per plugin.

The M377's − input is connected to the ACVS (Analog Control Voltage System) output.

The (differential) display outputs of the two amplifiers are hard-wired in parallel and drive the mainframe’s 50 Ω per side input impedance. The same is true of the trigger outputs of the two amplifiers.

The version of the M377 used in the 11A32 has a 100 Ω output impedance per side so that two of them in parallel create a source impedance of 50 Ω per side.

Each M377 amplifier's nominal common-mode output voltage is zero whether enabled or not. When not enabled, each M377 differential output is exactly zero by design. This fact is used during calibration by the plugin’s firmware to determine the mainframe’s imbalance and compensate for it during normal operation.

Each of the two channels has its own AUX output on dedicated pins of the plug-in interface connector:

signal name positive pin number negative pin number
AUX 1 B38 B37
AUX 2 A36 A35

See also the block diagram below.

Digital

The 11A32 and the 11A34 use exactly the same firmware.

The 11A34 and 11A32 were originally intended to use Intel 8052 microcontrollers. However, during development, the firmware swelled beyond that chip's 8192-byte maximum on-chip ROM size. Doug Haines found an alternate supplier of 8051-compatible chips (OKI Semiconductor) that offered a 16 KByte on-chip ROM, and that's what the plug-ins wound up with. The finished code size is about 14 KB. There are also units with the OKI M85C154 chip that has a piggyback EPROM (see photo below).

The 11A32 also contains a Dallas Semiconductor DS1220Y NVRAM storing last settings, calibration constants, and instrument serial number. The DS1220Y contains a battery with a typical life time of 20-30 years.

There is also an ACVS (Analog Control Voltage System) sample and hold module on a daughter board that generates the analog voltages needed for gain and offset, including error correction under microcontroller firmware control.

The microcontroller also provides the digital signals sent to the M377 amplifier, setting one of its six fixed gains, one of its three bandwidths, turning on or off its selected output, and each output's normal or invert state.

Digital mainframes do waveform manipulation (addition, subtraction, multiplication, etc.). Consequently only one 11A32 output is on at a time. Analog mainframes however allow more than one channel to be on at a time. This allows the plugin channels to be added or subtracted in the plugin.

Pictures

  • Block diagram

    Block diagram

  • 11A32 Input Attenuators

    11A32 Input Attenuators

  • 11A32 Kernel

    11A32 Kernel

  • 11A32 Analog Control and Signal Amplifiers

    11A32 Analog Control and Signal Amplifiers

  • 11A32 Main Interface

    11A32 Main Interface

  • left side internal

    left side internal

  • right side internal

    right side internal

Parts

Some Parts Used in the 11A32

Part Part Number(s) Class Description Used in
148-0086-00 148-0086-00 Discrete component miniature relay 11A32
Intel 8051 Monolithic integrated circuit 8-bit microcontroller 11A32 • 11A34 • WFM300
M377 165-2129-03 • 165-2089-06 • 155-2089-05 Monolithic integrated circuit amplifier 11A16 • 11A32 • 11A33 • 11A34 • 11A52 • 2245 • 2245A • 2247 • 2247A • 2252 • TDS410 • TDS420 • TDS460 • TDS520D • TDS540D • TDS580D • TDS680C • TDS684C • TDS714L • TDS724D • TDS754D • TDS784D
M474 Monolithic integrated circuit amplifier 11A32 • 11A34
Retrieved from "https://w140.com/tekwiki/index.php?title=11A32&oldid=97381"