7000 Series plug-in interface: Difference between revisions

Latest revision as of 02:15, 1 September 2024

Tektronix 7000 series oscilloscope mainframes have one (7912) or two vertical plug-in slots, and zero (7612D), one (7xx3, 7912) or two (7xx4) horizontal plug-in slots.

According to Barrie Gilbert in The Gears of Genius, the 7000 series backplane was largely developed by Les Larson.

The interconnect on either slot type is a 76-pin, 0.1" pitch PCB edge connector. The pinout on vertical and horizontal slots is not identical but compatible to the point that vertical plugins can be installed in horizontal slots and vice versa. However, in that case, some functions may be unavailable − for example, trigger signals are only routed to H slots so a timebase in a V slot must be externally triggered.

Looking into the mainframe from the front panel, "A" pins are left of the connector centerline (on the plug-in PCB's component side) and "B" are on the right (on the plug-in PCB's solder side). Pins are numbered from 1 at the bottom to 38 on the top. In the following table, (H) indicates signals available in horizontal slots only, (H-A) is horizontal slot A, (H-B) is horizontal slot B, and (V) denotes signals available in vertical slots only.

	A side		B side
Pin	Function		Function
1	Sweep Gate (H)		Delay mode ctl in (H-B)
2	Gate common		Delay mode ctl out (H-A)
3	A Sweep (V & H-A) [note 1]		B Sweep (V & H-B) [note 1]
4	Line trigger		Trigger holdoff (H)
5	Chop drive		Aux Swp gate (H)
6	Chop common		ALT drive
7	Intensity Limit (H)		MF Channel Switch
8	+5 V		Sweep inhibit (H)
9	+5 V (lights)		Delay gate (H)
10	Single sweep ready (H)		X comp inhibit (H)
11	+Signal		−Signal
12	Signal Ground		Signal Ground
13	+Trigger (V) [note 2]		−Trigger (V) [note 2]
14	Lights common		Dual beam Aux Y-Axis
15	Single sweep logic		Single sweep reset (H)
16	MF Mode		Aux Y axis (H)
17	Aux Z axis		Aux Z common
18	+15 V		−15 V
19	+50 V		−50 V
20	+Trigger in (H)		−Trigger in (H)
21	+Aux trigger in (H) [note 5]		−Aux trigger in (H) [note 5]
22	/EOI [note 6]		/SRQ [note 7]
23	/DAV		REN
24	/IFC [note 3]		/ATN
25	/NDAC		/NRFD
26	Logic Common		/SND or Inter-plugin GND [note 8]
27	−5.2 V [note 4]	Inter-plugin link	+5.1 V [note 4]	Inter-plugin link
28	Inter-plugin link		Inter-plugin link
29	TS10 [note 3]		TS9	DIO8
30	TS8	DIO7	TS7	DIO6
31	TS6	DIO5	TS5	DIO4
32	TS4	DIO3	TS3	DIO2
33	TS2	DIO1	TS1 [note 3]
34	n.c. [note 8]		n.c. [note 8]
35	Force readout		Plugin mode [note 9]
36	n.c. [note 8]		n.c.
37	Ch. 1 Col		Ch. 1 Row
38	Ch. 2 Col		Ch. 2 Row

Pin group function legend

Plugin power

HF signals

Readout system signals

IEEE-488 bus
(used in 7A16P, 7A29P, 7B90P, digitizer mainframes)

Power Supply Load Limits

According to Specification 704 (see also 7A17 manual), the total allowed DC power consumption for each plugin is 16.5 W, with the following individual current limits:

Supply Rail	Pin	Maximum Current
+5 V	A8	500 mA
+5 V Lights	A9	500 mA
+15 V	A18	500 mA
−15 V	B18	500 mA
+50 V	A19	100 mA
−50 V	B19	100 mA
−5.2 V [note 4]	A27	500 mA
+5.1 V [note 4]	B27	2 A

Notes

[note 1] Output from H plugins, input on V plugins

[note 2] Output from V plugins, unused and terminated 50 Ω to ground in mainframe H slots

[note 3] In programmable mainframes, A24 is clamped to not exceed +3 V, indicating to programmable plug-ins to use TS2-TS9 as GPIB lines and a modified readout logic using only TS1 and TS10, where TS1 is active in time slot 1, and TS10 is active in each time slot. Programmable plug-ins source at least 100 μA into TS10 (A29) indicating to a programmable mainframe that the alternative time-slot scheme is to be used.

[note 4] Not provided by most mainframes (digitizers only?). 7A16P connects B27 to A9, requires −5.2 V on A27.

[note 5] According to the 11000-series interface manual, many 7k plug-in units ground pin B21 or connect it to pin A21, and The 7D10, 7D11, 7D14, 7S14, and possibly some others have pin A21 grounded.

[note 6] A22 = Busy output from 7D12, 7D15; A22 = Delayed Sweep Gate output for 7B53A with mod. 769G, routed to real panel on 7403 or 7603 scopes with 769H mod.

[note 7] B22 = /Hold input to 7D12, 7D15. Mainframe connection or use unclear.

[note 8] Specification 704 (1976) says that A34 was intended as a "DVM line" (return on B35) and A36 as a "True time indicator" for a "proposed 2-dot measurement system" that was never implemented. A/B34 and A/B36 were physically removed from mainframes and plug-ins to reduce the possibility of shorts by mid-aligned plug-ins during insertion.

[note 9] The plug-in mode is supplied to the mainframe either as a resistor connected to ground (with 5% tolerance), or by supplying a DC voltage (with 0.25 V tolerance):

Plugin Mode	Resistance	Voltage
CH 1, Delaying, Intensified, Normal	≥30 kΩ	5 V
CH 2, Delayed Sweep	3.9 kΩ	4 V
ADD, Mixed Sweep	620 Ω	2 V
ALT	240 Ω	1 V
Chop	0-47 Ω	0 V

Description of signals

For detailed descriptions, see Specification 704 (1976)

Sweep Gate − 0/+5 V, high while sweep is running (beam unblanking), connected to +5 V in amplifier plugins; +Gate Output on mainframe uses Sweep Gate from H slot A when A Gate is selected, and from H slot B when B is selected.
Delay Mode Control − Output on delaying timebase in horizontal slot A, connected to input on delayed timebase in horizontal slot B. >+3 V disables auto sweep in delayed timebase; 0 V enables independent timebase function. Grounded in amplifier plugins.
A/B Sweep − 500 mV_p-p, negative-going copy of sweep signal from timebase, not affected by X position control or magnifier; Used for mainframe's Sawtooth Out, additionally fed to V plugins.
Line Trigger − Approx. 3 V_RMS mains-frequency signal from power supply (through transformer). Present on all slots.
Trigger Holdoff − 0/+5 V, generated by time-base, high during holdoff time of time-base, used in mainframe for ALT sequencing.
Chop Drive − 0/+5 V; switches at one-half the rate of the VERTICAL MODE CHOP signal; high level selects channel 2, low level selects channel 1 of a dual-trace plug-in.
Aux Sweep Gate − 0/+5 V; pulled high by dual-sweep time-base plug-ins during auxiliary sweep. Used to deliver the realtime clock signal from 7B87 to 7854.
Alt Drive − 0/+5 V; high level will display channel 2 of a dual-trace plug-in, low will display channel 1.
Intensity Limit − Switched to ground by timebase in slow sweep speeds (≥100 ms/Div), limits beam intensity to protect the CRT phosphor.
Mainframe Channel Switch − −0.6/+1.1 V logic levels; plug-in output is displayed when MF Channel Switch ≠ MF Mode (XOR).
Mainframe Mode − 0/+5 V logic levels; plug-in output is displayed when MF Channel Switch ≠ MF Mode (XOR).
Sweep Inhibit/Sweep Lockout - Mainframe injects current > 1 mA to prevent time base from sweeping. Used for ALT sequencing and delayed sweep of the B time base.
Delay Gate − negative-going pulse starting at the end of the delay period, and lasting until the end of the sweep from the delaying timebase. Mainframes connect this signal from the A timebase through a 2 k resistor and a diode to B8 Sweep inhibit of the B time base to trigger the delayed sweep. +Gate Output on mainframe uses Delay Gate from H slot B when Delay Gate is selected. Grounded in amplifier plugins.
Single sweep ready − 0/+5 V, high when single sweep is ready.
X comp. inhibit − Connected to ground in amplifiers, switched to ground by timebase set to amplifier (X-Y) mode to enable X-Y delay compensation in scopes with that function (7503, 7504 Opt.02, 7704 Opt.02, 7904 Opt.02, 7104 Opt.02).
Signal − Signal output from plugin to mainframe. Differential, 50 Ω per side. 50 mV/Div (differential).
Trigger − Copy of signal output from V plugin to mainframe. Differential, 50 Ω per side. 50 mV/Div (differential). Terminated on H slots.
Dual Beam Aux Y-Axis − Used in dual beam mainframes (7844), Current-driven input to mainframe allowing vertical separation of two traces with dual timebase plugins. 1 mA/Div sensitivity.
Single Sweep Logic − 0/+5 V; high level when time-base is in single sweep mode.
Single Sweep Reset − Switched to ground to reset single sweep.
Aux Y Axis − Current-driven input to mainframe allowing vertical separation of two traces with dual timebase plugins. 1 mA/Div sensitivity; driven only when plug-in output is displayed (see MF Ch Switch above). Not available in early mainframes e.g. 7504, 7704 non-A.
Aux Z Axis − Current-driven input to mainframe allowing plugins to modulate beam intensity, e.g. in dual timebase A intensified by B display mode; driven only when plug-in output is displayed (see MF Ch Switch above).
Trigger In − Trigger signal input on H plugin, routed from V plugin's trigger output. Differential, 50 Ω per side, 50 mV/Div (differential).
Aux Trigger In − Provided by 1^st generation 7000 series mainframes (7704, 7504, 7503, 7403N). Only known use is in the 7B52 timebase as an optional source for the delayed trigger. Four-bay mainframes supply the trigger signal from the left horizontal bay to Aux Trig In on the right horizontal bay and vice versa, via 510 Ω resistors. Three-bay mainframes supply the Left Vert trigger signal via 510 Ω resistors.
Inter-Plugin Connections − In 1^st generation 7000 series mainframes (7704, 7504, 7503, 7403N), pins 26B, 27A/B and 28A/B are inter-plugin connections. In the 3-bay mainframes, right vertical slot pins 27A, 27B, 28A, 28B are connected via 50 Ω striplines to horizontal slot pins 27B, 27A, 28B, 28A respectively, with ground on 26B. Four-slot mainframes additionally make the same connections from the left vertical slot to the right horizontal slot. Since no plug-ins were made that used these connections, they were left out from later mainframes.
GPIB lines − Control signal functions are the same as their IEEE-488 (GPIB) equivalents. Time slot lines 2 to 9 double as IEEE-488 data lines.
TS1−TS10 − readout system time slot pulses. Idle 0, active −15 V.
Force Readout − Allows plug-in readout information to be displayed regardless of the mainframe mode switch setting when pulled low (<0.5 V). Used by several 7DXX plug-ins.
Plugin Mode − 5-level signal providing the mainframe with information about the operating mode of a dual-trace or dual-sweep plugin. [note 9]
Ch1/2 Row/Col − Analog current inputs to the readout system. Ch1 refers to the first channel within the plugin slot in question and is associated with the readout field on top of the screen. Ch2 is the 2nd channel displayed at the bottom. Row/Current signals accept negative currents in 100 μA steps; typically, plugins contain resistors from time slot signal lines to row/current lines.

Links

Specifications

Extenders/Sockets

Prototype

After it was decided that there would be a "New Generation" series of lab scopes to replace the 500 series, concept prototypes were built. Before Howard Vollum decided on the height of the New Generation plug-ins, a taller form factor was being considered. This is what it looked like:

Very Early New Generation Plug-in Prototype
Very Early New Generation Plug-in Prototype
Very Early New Generation Plug-in Prototype
Very Early New Generation Plug-in Prototype

From On the History and Environment of Tektronix page 58:

But Howard then threw another challenge to his group: plug-in height. Work up through late 1966 had assumed a seven inch plug-in height which would provide room for the needed components using readily available and proven parts. But the H-P scopes were smaller in size and quite attractive in appearance. So, one day, Howard said, "the plug-ins will be 5 1/2 inches in height."
Oliver Dalton recalls the decision to reduce the plug-in height as a traumatic one: "The decision set us back at least one year for the height decision required three major electro-mechanical component efforts in addition to the IC read-out effort: 1) new lit push-buttons ... we needed 25 on a panel; 2) cam switches - these were Howard's ideas ... we needed them to be small and reasonably cheap; 3) relays ... we needed them to be small and reliable. We then largely had to make do with other available parts, like potentiometers."

@@ Line 1: / Line 1: @@
-The [[7000-series scopes]] have two categories of slots, horizontal and vertical, that have partly different but compatible interconnects so that vertical plugins can be installed in horizontal slots and vice versa, but not with all functions.
+'''[[7000-series scopes|Tektronix 7000 series oscilloscope mainframes]]''' have one ([[7912]]) or two vertical plug-in slots, and zero ([[7612D]]), one (7xx3, 7912) or two (7xx4) horizontal plug-in slots.
-The interconnect is a 76-pin PCB edge connector.  Looking into the mainframe from the front panel, "A" pins are left and "B" are right of the connector centerline, and pins are numbered from 1 at the bottom to 38 on the top. (A pins are on the [[:File:Tek-7a17-left-board.jpg|plug-in PCB's component side]], B pins on the [[:File:Tek-7a17-right-board.jpg|solder side]].) In the following table, (H) indicates signals available in horizontal slots only, (H-A) is horizontal slot A, (H-B) is horizontal slot B, and (V) denotes signals available in vertical slots only.
+According to [[Barrie Gilbert]] in [https://ieeexplore.ieee.org/stamp/stamp.jsp?arnumber=4785651 ''The Gears of Genius''], the 7000 series backplane was largely developed by [[Les Larson]].
+The interconnect on either slot type is a 76-pin, 0.1" pitch PCB edge connector. The pinout on vertical and horizontal slots is not identical but
+compatible to the point that vertical plugins can be installed in horizontal slots and vice versa. However, in that case, some functions may
+be unavailable − for example, trigger signals are only routed to H slots so a timebase in a V slot must be externally triggered.
+Looking into the mainframe from the front panel, "A" pins are left of the connector centerline (on the [[Media:Tek-7a17-left-board.jpg|plug-in PCB's component side]]) and "B" are on the right (on the [[Media:Tek-7a17-right-board.jpg|plug-in PCB's solder side]]). Pins are numbered from 1 at the bottom to 38 on the top.
+In the following table, (H) indicates signals available in horizontal slots only, (H-A) is horizontal slot A, (H-B) is horizontal slot B, and (V) denotes signals available in vertical slots only.
+{|border="0"
+|- valign="top"
+| width="400px" |
-{|
-|- valign="top" border="1"
-| width="26em" |
 {| class="wikitable"
 |-
 !width="10%"|&nbsp;
-!width="45%"| A side
+!colspan="2"| A side
-!width="45%"| B side
+!colspan="2"| B side
 |-
 ! Pin
-! Function
+! colspan="2" | Function
-! Function
+! colspan="2" | Function
 |-
-|  1 || Sweep Gate (H)  || Delay mode ctl in (H-B)
+|  1
+| colspan="2" | Sweep Gate (H)
+| colspan="2" | Delay mode ctl in (H-B)
 |-
-|  2 || Gate common  || Delay mode ctl out (H-A)
+|  2
+| colspan="2" | Gate common
+| colspan="2" | Delay mode ctl out (H-A)
 |-
-|  3 || A Sweep (H-A,V) ''[note 1]''    || B Sweep (H-B,V) ''[note 1]''
+|  3
+| colspan="2" | A Sweep (V &amp; H-A) ''[note 1]''
+| colspan="2" | B Sweep (V &amp; H-B) ''[note 1]''
 |-
-|  4 || Line trigger || Trigger holdoff (H)
+|  4
+| colspan="2" | Line trigger
+| colspan="2" | Trigger holdoff (H)
 |-
-|  5 || Chop drive   || Aux Swp gate (H)
+|  5
+| colspan="2" | Chop drive
+| colspan="2" | Aux Swp gate (H)
 |-
-|  6 || Chop common  || ALT drive
+|  6
+| colspan="2" | Chop common
+| colspan="2" | ALT drive
 |-
-|  7 || Intensity Limit (H) || MF Channel Switch
+|  7
+| colspan="2" | Intensity Limit (H)
+| colspan="2" | MF Channel Switch
 |-
-|  8 || bgcolor="Pink"| +5 V  ||  Sweep inhibit (H)
+|  8
+| colspan="2" bgcolor="Pink" | +5 V
+| colspan="2" |  Sweep inhibit (H)
 |-
-|  9 || bgcolor="Pink"| +5 V (lights)  || Delay gate (H)
+|  9
+| colspan="2" bgcolor="Pink" | +5 V (lights)
+| colspan="2" | Delay gate (H)
 |-
-| 10 || Single sweep ready (H)  ||  X comp inhibit (H)
+| 10
+| colspan="2" | Single sweep ready (H)
+| colspan="2" |  X comp inhibit (H)
 |- bgcolor="Yellow"
-| 11 || +Signal || −Signal
+| 11
+| colspan="2" | +Signal
+| colspan="2" | −Signal
 |- bgcolor="Pink"
-| 12 || Signal Ground || Signal Ground
+| 12
+| colspan="2" | Signal Ground
+| colspan="2" | Signal Ground
 |- bgcolor="Yellow"
-| 13 || +Trigger (V) ''[note 2]'' ||  −Trigger (V) ''[note 2]''
+| 13
+| colspan="2" | +Trigger (V) ''[note 2]''
+| colspan="2" |  −Trigger (V) ''[note 2]''
 |-
-| 14 || bgcolor="Pink"| Lights common || Dual beam Aux Y-Axis ([[7844]])
+| 14
+| colspan="2" bgcolor="Pink" | Lights common
+| colspan="2" | Dual beam Aux Y-Axis
 |-
-| 15 || Single sweep logic || Single sweep reset (H)
+| 15
+| colspan="2" | Single sweep logic
+| colspan="2" | Single sweep reset (H)
 |-
-| 16 || MF Mode  || Aux Y axis  (H)
+| 16
+| colspan="2" | MF Mode
+| colspan="2" | Aux Y axis  (H)
 |-
-| 17 || Aux Z axis  || Aux Z common
+| 17
+| colspan="2" | Aux Z axis
+| colspan="2" | Aux Z common
 |- bgcolor="Pink"
-| 18 || +15 V  || -15 V
+| 18
+| colspan="2" | +15 V
+| colspan="2" | −15 V
 |- bgcolor="Pink"
-| 19 || +50 V  || -50 V
+| 19
+| colspan="2" | +50 V
+| colspan="2" | −50 V
 |- bgcolor="Yellow"
-| 20 || +Trigger in (H) || −Trigger in (H)
+| 20
+| colspan="2" | +Trigger in (H)
+| colspan="2" | −Trigger in (H)
 |- bgcolor="Yellow"
-| 21 || +Aux trigger in (H) || −Aux trigger in (H)
+| 21
+| colspan="2" | +Aux trigger in (H) ''[note 5]''
+| colspan="2" | −Aux trigger in (H) ''[note 5]''
 |- bgcolor="LightBlue"
-| 22 || /EOI  || /SRQ
+| 22
+| colspan="2" | /EOI ''[note 6]''
+| colspan="2" | /SRQ ''[note 7]''
 |- bgcolor="LightBlue"
-| 23 || /DAV  || REN
+| 23
+| colspan="2" | /DAV
+| colspan="2" | REN
 |- bgcolor="LightBlue"
-| 24 || /IFC  || /ATN
+| 24
+| colspan="2" | /IFC  ''[note 3]''
+| colspan="2" | /ATN
 |- bgcolor="LightBlue"
-| 25 || /NDAC || /NRFD
+| 25
+| colspan="2" | /NDAC
+| colspan="2" | /NRFD
 |- bgcolor="LightBlue"
-| 26 || Logic Common || /SND
+| 26
-|- bgcolor="Pink"
+| colspan="2" | Logic Common
-| 27 || -5.2 V ''[note 3]''|| 5.1 V ''[note 3]''
+| colspan="2" | /SND <br />or Inter-plugin GND ''[note 8]''
+|-
+| 27
+| bgcolor="Pink" | −5.2 V<br />''[note 4]''
+| Inter-plugin<br />link
+| bgcolor="Pink" | +5.1 V<br />''[note 4]''
+| Inter-plugin<br />link
 |-
-| 28 || n.c. || n.c.
+| 28
+| colspan="2" | Inter-plugin link
+| colspan="2" | Inter-plugin link
 |- bgcolor="LightGreen"
-| 29 || TS10  || TS9 ''(DIO8)''
+| 29
-|- bgcolor="LightGreen"
+| colspan="2" | TS10  ''[note 3]''
-| 30 || TS8 ''(DIO7)''  || TS7 ''(DIO6)''
+| bgcolor="LightGreen" | TS9
-|- bgcolor="LightGreen"
+| bgcolor="LightBlue"  | ''DIO8''
-| 31 || TS6 ''(DIO5)''  || TS5 ''(DIO4)''
+|-
-|- bgcolor="LightGreen"
+| 30
-| 32 || TS4 ''(DIO3)''  || TS3 ''(DIO2)''
+| bgcolor="LightGreen" | TS8
-|- bgcolor="LightGreen"
+| bgcolor="LightBlue"  | ''DIO7''
-| 33 || TS2 ''(DIO1)''  || TS1
+| bgcolor="LightGreen" | TS7
+| bgcolor="LightBlue"  | ''DIO6''
+|-
+| 31
+| bgcolor="LightGreen" | TS6
+| bgcolor="LightBlue"  | ''DIO5''
+| bgcolor="LightGreen" | TS5
+| bgcolor="LightBlue"  | ''DIO4''
+|-
+| 32
+| bgcolor="LightGreen" | TS4
+| bgcolor="LightBlue"  | ''DIO3''
+| bgcolor="LightGreen" | TS3
+| bgcolor="LightBlue"  | ''DIO2''
+|-
+| 33
+| bgcolor="LightGreen" | TS2
+| bgcolor="LightBlue"  | ''DIO1''
+| colspan="2" bgcolor="LightGreen" | TS1 ''[note 3]''
 |-
-| 34 || n.c.  || n.c.
+| 34
-|- bgcolor="LightGreen"
+| colspan="2" | n.c. ''[note 8]''
-| 35 || Force readout || Plugin mode
+| colspan="2" | n.c. ''[note 8]''
+|-
+| 35
+| colspan="2" bgcolor="LightGreen" | Force readout
+| colspan="2" | Plugin mode ''[note 9]''
 |-
-| 36 || n.c. || n.c.
+| 36
+| colspan="2" | n.c. ''[note 8]''
+| colspan="2" | n.c.
 |- bgcolor="LightGreen"
-| 37 || Ch. 1 Col  || Ch. 1 Row
+| 37
+| colspan="2" | Ch. 1 Col
+| colspan="2" | Ch. 1 Row
 |- bgcolor="LightGreen"
-| 38 || Ch. 2 Col  || Ch. 2 Row
+| 38
+| colspan="2" | Ch. 2 Col
+| colspan="2" | Ch. 2 Row
 |-
 |}
 ===Pin group function legend===
-:{|
+{| cellpadding="4"
 |-
 | bgcolor="Pink" | Plugin power
@@ Line 103: / Line 197: @@
 | bgcolor="LightGreen" | [[7000 series readout system|Readout system]] signals
 |-
-| bgcolor="LightBlue"  | IEEE-488 bus used in [[7A16P]], [[7A29P]], [[7B90P]], digitizer mainframes; data 1-8 on TS2-TS9 lines
+| bgcolor="LightBlue"  | IEEE-488 bus<br /> (used in [[7A16P]], [[7A29P]], [[7B90P]], digitizer mainframes)
+|}
+===Power Supply Load Limits===
+According to [[Media:Tek 7000-series plug-in mainframe interface manual ocr.pdf| Specification 704]] (see also [[7A17]] manual), the total allowed DC power consumption for each plugin is 16.5 W, with the following individual current limits:
+:{| class="wikitable"
+|-
+|-
+! Supply Rail
+! Pin
+! Maximum Current
+|-
+|  +5 V || A8  || 500 mA
+|-
+|  +5 V Lights || A9 || 500 mA
+|-
+|  +15 V || A18   || 500 mA
+|-
+|  −15 V || B18  || 500 mA
+|-
+|  +50 V || A19  || 100 mA
+|-
+|  −50 V || B19  || 100 mA
+|-
+|  −5.2 V ''[note 4]'' || A27 || 500 mA
+|-
+|  +5.1 V ''[note 4]'' || B27 || 2 A
 |}
+===Notes===
+''[note 1]'' Output from H plugins, input on V plugins
+''[note 2]'' Output from V plugins, unused and terminated 50 Ω to ground in mainframe H slots
+''[note 3]'' In programmable mainframes, A24 is clamped to not exceed +3 V, indicating to programmable plug-ins to use TS2-TS9 as GPIB lines and a modified readout logic using only TS1 and TS10, where TS1 is active in time slot 1, and TS10 is active in each time slot. Programmable plug-ins source at least 100 μA into TS10 (A29) indicating to a programmable mainframe that the alternative time-slot scheme is to be used.
+''[note 4]'' Not provided by most mainframes (digitizers only?). [[7A16P]] connects B27 to A9, requires −5.2 V on A27.
+''[note 5]'' According to the [[Media:Tek 11000-series plug-in to main frame interface manual.pdf|11000-series interface manual]], ''many 7k plug-in units ground pin B21 or connect it to pin A21'', and ''The [[7D10]], [[7D11]], [[7D14]], [[7S14]], and possibly some others have pin A21 grounded''.
+''[note 6]'' A22 = Busy output from [[7D12]], [[7D15]]; A22 = Delayed Sweep Gate output for [[7B53A]] with [[media:7B53A_MOD.pdf|mod. 769G]], routed to real panel on [[7403]] or [[7603]] scopes with 769H mod.
+''[note 7]'' B22 = /Hold input to 7D12, 7D15. Mainframe connection or use unclear.
+''[note 8]'' [[Media:Tek 7000-series plug-in mainframe interface manual ocr.pdf|Specification 704 (1976)]] says that A34 was intended as a "DVM line" (return on B35) and A36 as a "True time indicator" for a "proposed 2-dot measurement system" that was never implemented. A/B34 and A/B36 were physically removed from mainframes and plug-ins to reduce the possibility of shorts by mid-aligned plug-ins during insertion.
+''[note 9]'' The plug-in mode is supplied to the mainframe either as a resistor connected to ground (with 5% tolerance), or by supplying a DC voltage (with 0.25 V tolerance):
+:{| class="wikitable"
+|-
+|-
+! Plugin Mode
+! Resistance
+! Voltage
+|-
+| CH 1, Delaying, Intensified, Normal || ≥30 kΩ  || 5 V
+|-
+| CH 2, Delayed Sweep || 3.9 kΩ || 4 V
+|-
+| ADD, Mixed Sweep || 620 Ω || 2 V
+|-
+| ALT || 240 Ω || 1 V
+|-
+| Chop || 0-47 Ω || 0 V
+|}
+[[Image:7000 slot pinout.jpg|thumb|400px|left]]
 |
 ===Description of signals===
-* ''Sweep Gate'' − 0/+5 V, high while sweep is running (beam unblanking); +Gate Output on mainframe uses Sweep Gate from H slot A when A Gate is selected, and from H slot B when B is selected
+''For detailed descriptions, see [[Media:Tek 7000-series plug-in mainframe interface manual ocr.pdf|Specification 704 (1976)]]''
-* ''Delay Mode Control'' − Output on delaying timebase in horizontal slot A, connected to input on delayed timebase in horizontal slot B.  >+3 V disables auto sweep in delayed timebase; 0 V enables independent timebase function.
+* ''Sweep Gate'' − 0/+5 V, high while sweep is running (beam unblanking), connected to +5 V in amplifier plugins; +Gate Output on mainframe uses Sweep Gate from H slot A when A Gate is selected, and from H slot B when B is selected.
-* ''A/B Sweep'' − 500 mV<sub>p-p</sub>, negative-going copy of sweep signal from timebase, used for mainframe's Sawtooth Out, additionally fed to V plugins
+* ''Delay Mode Control'' − Output on delaying timebase in horizontal slot A, connected to input on delayed timebase in horizontal slot B.  >+3 V disables auto sweep in delayed timebase; 0 V enables independent timebase function.  Grounded in amplifier plugins.
-* ''Line Trigger'' − Approx. 1 V<sub>RMS</sub> mains-frequency signal from power supply (through transformer)
+* ''A/B Sweep'' − 500 mV<sub>p-p</sub>, negative-going copy of sweep signal from timebase, not affected by X position control or magnifier; Used for mainframe's Sawtooth Out, additionally fed to V plugins.
-* ''Trigger Holdoff'' −
+* ''Line Trigger'' − Approx. 3 V<sub>RMS</sub> mains-frequency signal from power supply (through transformer). ''Present on all slots.''
-* ''Chop Drive'' −
+* ''Trigger Holdoff'' − 0/+5 V, generated by time-base, high during holdoff time of time-base, used in mainframe for ALT sequencing.
-* ''Chop Mode Sense'' −
+* ''Chop Drive'' − 0/+5 V; switches at one-half the rate of the VERTICAL MODE CHOP signal; high level selects channel 2, low level selects channel 1 of a dual-trace plug-in.
-* ''Aux Sweep Gate'' −
+* ''Aux Sweep Gate'' − 0/+5 V; pulled high by dual-sweep time-base plug-ins during auxiliary sweep. Used to deliver the realtime clock signal from [[7B87]] to [[7854]].
-* ''Alt Drive'' −
+* ''Alt Drive'' − 0/+5 V; high level will display channel 2 of a dual-trace plug-in, low will display channel 1.
-* ''Intensity Limit'' −
+* ''Intensity Limit'' − Switched to ground by timebase in slow sweep speeds (≥100 ms/Div), limits beam intensity to protect the CRT [[phosphor]].
-* ''Mainframe Channel Switch'' −
+* ''Mainframe Channel Switch'' − −0.6/+1.1 V logic levels; plug-in output is displayed when MF Channel Switch ≠ MF Mode (XOR).
-* ''Sweep Inhibit'' −
+* ''Mainframe Mode'' − 0/+5 V logic levels; plug-in output is displayed when MF Channel Switch ≠ MF Mode (XOR).
-* ''Delay Gate'' − +Gate Output on mainframe uses Delay Gate from H slot B when Delay Gate is selected
+* ''Sweep Inhibit/Sweep Lockout'' - Mainframe injects current > 1 mA to prevent time base from sweeping. Used for ALT sequencing and delayed sweep of the ''B'' time base.
-* ''Single sweep ready'' −
+* ''Delay Gate'' − negative-going pulse starting at the end of the delay period, and lasting until the end of the sweep from the delaying timebase. Mainframes connect this signal from the ''A'' timebase through a 2 k resistor and a diode to B8 ''Sweep inhibit'' of the ''B'' time base to trigger the delayed sweep. +Gate Output on mainframe uses Delay Gate from H slot B when Delay Gate is selected.  Grounded in amplifier plugins.
-* ''X comp. inhibit'' − Connected to ground in amplifiers, switched to ground by timebase set to amplifier (X-Y) mode to enable X-Y delay compensation in scopes with that function ([[7904|7904 Opt.2]], [[7104|7104 Opt.2]])
+* ''Single sweep ready'' − 0/+5 V, high when single sweep is ready.
+* ''X comp. inhibit'' − Connected to ground in amplifiers, switched to ground by timebase set to amplifier (X-Y) mode to enable X-Y delay compensation in scopes with that function ([[7503]], [[7504|7504 Opt.02]], [[7704|7704 Opt.02]], [[7904|7904 Opt.02]], [[7104|7104 Opt.02]]).
 * ''Signal'' − Signal output from plugin to mainframe.  Differential, 50 Ω per side. 50 mV/Div (differential).
-* ''Trigger'' − Copy of signal output from V plugin to mainframe.  Differential, 50 Ω per side. 50 mV/Div (differential).
+* ''Trigger'' − Copy of signal output from V plugin to mainframe.  Differential, 50 Ω per side. 50 mV/Div (differential). Terminated on H slots.
-* ''Aux Y-Axis'' − Current-driven input to mainframe allowing vertical separation of two traces with dual timebase plugins.
+* ''Dual Beam Aux Y-Axis'' − Used in dual beam mainframes ([[7844]]), Current-driven input to mainframe allowing vertical separation of two traces with dual timebase plugins. 1 mA/Div sensitivity.
-* ''Dual Beam Aux Y-Axis'' −
+* ''Single Sweep Logic'' − 0/+5 V; high level when time-base is in single sweep mode.
-* ''Single Sweep Logic'' −
+* ''Single Sweep Reset'' − Switched to ground to reset single sweep.
-* ''Single Sweep Reset'' −
+* ''Aux Y Axis'' − Current-driven input to mainframe allowing vertical separation of two traces with dual timebase plugins. 1 mA/Div sensitivity; driven only when plug-in output is displayed (see ''MF Ch Switch'' above).  Not available in early mainframes e.g. [[7504]], [[7704]] non-A.
-* ''Mainframe Mode'' −
+* ''Aux Z Axis'' − Current-driven input to mainframe allowing plugins to modulate beam intensity, e.g. in dual timebase A intensified by B display mode; driven only when plug-in output is displayed (see ''MF Ch Switch'' above).
-* ''Aux Z Axis'' − Current-driven input to mainframe allowing plugins to modulate beam intensity, e.g. in dual timebase A intensified by B display mode.
+* ''Trigger In'' − Trigger signal input on H plugin, routed from V plugin's trigger output.  Differential, 50 Ω per side, 50 mV/Div (differential).
-* ''Trigger In'' − Trigger signal input on H plugin, routed from V plugin's trigger output.  Differential, 50 Ω per side.
+* ''Aux Trigger In'' − Provided by 1<sup>st</sup> generation 7000 series mainframes ([[7704]], [[7504]], [[7503]], [[7403N]]).  Only known use is in the [[7B52]] timebase as an optional source for the delayed trigger.  Four-bay mainframes supply the trigger signal from the left horizontal bay to Aux Trig In on the right horizontal bay and vice versa, via 510 Ω resistors.  Three-bay mainframes supply the Left Vert trigger signal via 510 Ω resistors.
-* ''Aux Trigger In'' −
+* ''Inter-Plugin Connections'' − In 1<sup>st</sup> generation 7000 series mainframes ([[7704]], [[7504]], [[7503]], [[7403N]]), pins 26B, 27A/B and 28A/B are inter-plugin connections.  In the 3-bay mainframes, right vertical slot pins 27A, 27B, 28A, 28B are connected via 50 Ω striplines to horizontal slot pins 27B, 27A, 28B, 28A respectively, with ground on 26B.  Four-slot mainframes additionally make the same connections from the left vertical slot to the right horizontal slot.  Since no plug-ins were made that used these connections, they were left out from later mainframes.
 * ''GPIB lines'' − Control signal functions are the same as their [[GPIB interface|IEEE-488 (GPIB)]] equivalents.  Time slot lines 2 to 9 double as IEEE-488 data lines.
 * ''TS1−TS10'' − [[7000 series readout system|readout system]] time slot pulses.  Idle 0, active −15 V.
-* ''Force Readout'' −
+* ''Force Readout'' − Allows plug-in readout information to be displayed regardless of the mainframe mode switch setting when pulled low (<0.5 V). Used by several 7DXX plug-ins.
-* ''Plugin Mode'' −
+* ''Plugin Mode'' − 5-level signal providing the mainframe with information about the operating mode of a dual-trace or dual-sweep plugin. ''[note 9]''
 * ''Ch1/2 Row/Col'' − Analog current inputs to the readout system. Ch1 refers to the first channel within the plugin slot in question and is associated with the readout field on top of the screen. Ch2 is the 2nd channel displayed at the bottom.  Row/Current signals accept negative currents in 100 μA steps; typically, plugins contain resistors from time slot signal lines to row/current lines.
 |}
-===Notes===
+==Links==
-''[note 1]'' output from H plugins, input on V plugins
+'''Specifications'''
+* '''[[Media:Tek 7000-series plug-in mainframe interface manual ocr.pdf|Tektronix Specification 704, 7000-Series Plug-in to Mainframe Interface Manual]], 1976'''
-''[note 2]'' output from V plugins, unused and terminated 50 Ω to ground in mainframe H slots
+* [[Media:Introduction to the 7000 Series Switching and Logic Circuits (Ken Parker, 1970).pdf| Introduction to the 7000 Series Switching and Logic Circuits]] (Ken Parker, 1970
+* [https://archive.org/details/tektronix_7000_backplane_Pin_Out Kahrs, ''Interfacing to the Tektronix 7000 series'']
+'''Extenders/Sockets'''
+* [[067-0589-00|067-0589-00 rigid extender]]
+* [[067-0616-00|067-0616-00 flexible extender]]
+* [https://www.ecosensory.com/tek/tek_7K_flex_sales_blurb.txt John Griessen's flex extender kit] / [https://www.ecosensory.com/tek/TEK_7K_FLEX_assy-013-sm.jpg Photo]
+* [[Repairing 7000-series plug-in sockets]]
-''[note 3]'' not provided by most mainframes (digitizers only?). [[7A16P]] connects B27 to A9, requires -5.2 V on A27.
+==Prototype==
+After it was decided that there would be a "New Generation" series of lab scopes to replace the [[500-series scopes|500 series]], concept prototypes were built.
+Before [[Howard Vollum]] decided on the height of the New Generation plug-ins, a taller form factor was being considered. This is what it looked like:
+<gallery>
+Tek 7k concept plug-in pre-prototype 1.jpg|Very Early New Generation Plug-in Prototype
+Tek 7k concept plug-in pre-prototype 2.jpg|Very Early New Generation Plug-in Prototype
+Tek 7k concept plug-in pre-prototype 3.jpg|Very Early New Generation Plug-in Prototype
+Tek 7k concept plug-in pre-prototype 4.jpg|Very Early New Generation Plug-in Prototype
+</gallery>
-==Links==
+From [[Media:On-The-History-And-Environment-Of-Tektronix.pdf|On the History and Environment of Tektronix]] page 58:
+<blockquote>
+But [[Howard Vollum|Howard]] then threw another challenge to his group: plug-in height.
+Work up through late 1966 had assumed a seven inch plug-in height which would provide room for the needed components using readily available and proven parts.
+But the H-P scopes were smaller in size and quite attractive in appearance.
+So, one day, Howard said, "the plug-ins will be 5 1/2 inches in height."
-* [https://archive.org/details/tektronix_7000_backplane_Pin_Out Kahrs, ''Interfacing to the Tektronix 7000 series'']
+[[Oliver Dalton]] recalls the decision to reduce the plug-in height as a traumatic one:
+"The decision set us back at least one year for the height decision required three major electro-mechanical component efforts in addition to the [[7000 series readout system|IC read-out effort]]: 1) new [[Back-lit switches|lit push-buttons]] ... we needed 25 on a panel; 2) [[cam switch]]es - these were Howard's ideas ... we needed them to be small and reasonably cheap; 3) [[Miniature relays|relays]] ... we needed them to be small and reliable. We then largely had to make do with other available parts, like potentiometers."
+</blockquote>
 [[Category:Plug-in interfaces]]