7000 Series plug-in interface

Tektronix 7000 series oscilloscope mainframes have one (7912) or two vertical plug-in slots, and zero (7612D), one (7xx3, 7912) or two (7xx4) horizontal plug-in slots.

According to Barrie Gilbert in The Gears of Genius, the 7000 series backplane was largely developed by Les Larson.

The interconnect on either slot type is a 76-pin, 0.1" pitch PCB edge connector. The pinout on vertical and horizontal slots is not identical but compatible to the point that vertical plugins can be installed in horizontal slots and vice versa. However, in that case, some functions may be unavailable − for example, trigger signals are only routed to H slots so a timebase in a V slot must be externally triggered.

Looking into the mainframe from the front panel, "A" pins are left of the connector centerline (on the plug-in PCB's component side) and "B" are on the right (on the plug-in PCB's solder side). Pins are numbered from 1 at the bottom to 38 on the top. In the following table, (H) indicates signals available in horizontal slots only, (H-A) is horizontal slot A, (H-B) is horizontal slot B, and (V) denotes signals available in vertical slots only.

A side B side Pin Function Function 1 Sweep Gate (H) Delay mode ctl in (H-B) 2 Gate common Delay mode ctl out (H-A) 3 A Sweep (V & H-A) [note 1] B Sweep (V & H-B) [note 1] 4 Line trigger Trigger holdoff (H) 5 Chop drive Aux Swp gate (H) 6 Chop common ALT drive 7 Intensity Limit (H) MF Channel Switch 8 +5 V Sweep inhibit (H) 9 +5 V (lights) Delay gate (H) 10 Single sweep ready (H) X comp inhibit (H) 11 +Signal −Signal 12 Signal Ground Signal Ground 13 +Trigger (V) [note 2] −Trigger (V) [note 2] 14 Lights common Dual beam Aux Y-Axis 15 Single sweep logic Single sweep reset (H) 16 MF Mode Aux Y axis (H) 17 Aux Z axis Aux Z common 18 +15 V −15 V 19 +50 V −50 V 20 +Trigger in (H) −Trigger in (H) 21 +Aux trigger in (H) [note 5] −Aux trigger in (H) [note 5] 22 /EOI [note 6] /SRQ [note 7] 23 /DAV REN 24 /IFC [note 3] /ATN 25 /NDAC /NRFD 26 Logic Common /SND or Inter-plugin GND [note 8] 27 −5.2 V [note 4] Inter-plugin link +5.1 V [note 4] Inter-plugin link 28 Inter-plugin link Inter-plugin link 29 TS10 [note 3] TS9 DIO8 30 TS8 DIO7 TS7 DIO6 31 TS6 DIO5 TS5 DIO4 32 TS4 DIO3 TS3 DIO2 33 TS2 DIO1 TS1 [note 3] 34 n.c. [note 8] n.c. [note 8] 35 Force readout Plugin mode [note 9] 36 n.c. [note 8] n.c. 37 Ch. 1 Col Ch. 1 Row 38 Ch. 2 Col Ch. 2 Row Pin group function legend Plugin power HF signals Readout system signals IEEE-488 bus  (used in 7A16P, 7A29P, 7B90P, digitizer mainframes)  Power Supply Load Limits According to Specification 704 (see also 7A17 manual), the total allowed DC power consumption for each plugin is 16.5 W, with the following individual current limits: Supply Rail Pin Maximum Current +5 V A8 500 mA +5 V Lights A9 500 mA +15 V A18 500 mA −15 V B18 500 mA +50 V A19 100 mA −50 V B19 100 mA −5.2 V [note 4] A27 500 mA +5.1 V [note 4] B27 2 A Notes [note 1] Output from H plugins, input on V plugins [note 2] Output from V plugins, unused and terminated 50 Ω to ground in mainframe H slots [note 3] In programmable mainframes, A24 is clamped to not exceed +3 V, indicating to programmable plug-ins to use TS2-TS9 as GPIB lines and a modified readout logic using only TS1 and TS10, where TS1 is active in time slot 1, and TS10 is active in each time slot. Programmable plug-ins source at least 100 μA into TS10 (A29) indicating to a programmable mainframe that the alternative time-slot scheme is to be used. [note 4] Not provided by most mainframes (digitizers only?). 7A16P connects B27 to A9, requires −5.2 V on A27. [note 5] According to the 11000-series interface manual, many 7k plug-in units ground pin B21 or connect it to pin A21, and The 7D10, 7D11, 7D14, 7S14, and possibly some others have pin A21 grounded. [note 6] A22 = Busy output from 7D12, 7D15; A22 = Delayed Sweep Gate output for 7B53A with mod. 769G, routed to real panel on 7403 or 7603 scopes with 769H mod. [note 7] B22 = /Hold input to 7D12, 7D15. Mainframe connection or use unclear. [note 8] Specification 704 (1976) says that A34 was intended as a "DVM line" (return on B35) and A36 as a "True time indicator" for a "proposed 2-dot measurement system" that was never implemented. A/B34 and A/B36 were physically removed from mainframes and plug-ins to reduce the possibility of shorts by mid-aligned plug-ins during insertion. [note 9] The plug-in mode is supplied to the mainframe either as a resistor connected to ground (with 5% tolerance), or by supplying a DC voltage (with 0.25 V tolerance): Plugin Mode Resistance Voltage CH 1, Delaying, Intensified, Normal ≥30 kΩ 5 V CH 2, Delayed Sweep 3.9 kΩ 4 V ADD, Mixed Sweep 620 Ω 2 V ALT 240 Ω 1 V Chop 0-47 Ω 0 V

Description of signals For detailed descriptions, see Specification 704 (1976) Sweep Gate − 0/+5 V, high while sweep is running (beam unblanking), connected to +5 V in amplifier plugins; +Gate Output on mainframe uses Sweep Gate from H slot A when A Gate is selected, and from H slot B when B is selected. Delay Mode Control − Output on delaying timebase in horizontal slot A, connected to input on delayed timebase in horizontal slot B. >+3 V disables auto sweep in delayed timebase; 0 V enables independent timebase function. Grounded in amplifier plugins. A/B Sweep − 500 mVp-p, negative-going copy of sweep signal from timebase, not affected by X position control or magnifier; Used for mainframe's Sawtooth Out, additionally fed to V plugins. Line Trigger − Approx. 3 VRMS mains-frequency signal from power supply (through transformer). Present on all slots. Trigger Holdoff − 0/+5 V, generated by time-base, high during holdoff time of time-base, used in mainframe for ALT sequencing. Chop Drive − 0/+5 V; switches at one-half the rate of the VERTICAL MODE CHOP signal; high level selects channel 2, low level selects channel 1 of a dual-trace plug-in. Aux Sweep Gate − 0/+5 V; pulled high by dual-sweep time-base plug-ins during auxiliary sweep. Used to deliver the realtime clock signal from 7B87 to 7854. Alt Drive − 0/+5 V; high level will display channel 2 of a dual-trace plug-in, low will display channel 1. Intensity Limit − Switched to ground by timebase in slow sweep speeds (≥100 ms/Div), limits beam intensity to protect the CRT phosphor. Mainframe Channel Switch − −0.6/+1.1 V logic levels; plug-in output is displayed when MF Channel Switch ≠ MF Mode (XOR). Mainframe Mode − 0/+5 V logic levels; plug-in output is displayed when MF Channel Switch ≠ MF Mode (XOR). Sweep Inhibit/Sweep Lockout - Mainframe injects current > 1 mA to prevent time base from sweeping. Used for ALT sequencing and delayed sweep of the B time base. Delay Gate − negative-going pulse starting at the end of the delay period, and lasting until the end of the sweep from the delaying timebase. Mainframes connect this signal from the A timebase through a 2 k resistor and a diode to B8 Sweep inhibit of the B time base to trigger the delayed sweep. +Gate Output on mainframe uses Delay Gate from H slot B when Delay Gate is selected. Grounded in amplifier plugins. Single sweep ready − 0/+5 V, high when single sweep is ready. X comp. inhibit − Connected to ground in amplifiers, switched to ground by timebase set to amplifier (X-Y) mode to enable X-Y delay compensation in scopes with that function (7503, 7504 Opt.02, 7704 Opt.02, 7904 Opt.02, 7104 Opt.02). Signal − Signal output from plugin to mainframe. Differential, 50 Ω per side. 50 mV/Div (differential). Trigger − Copy of signal output from V plugin to mainframe. Differential, 50 Ω per side. 50 mV/Div (differential). Terminated on H slots. Dual Beam Aux Y-Axis − Used in dual beam mainframes (7844), Current-driven input to mainframe allowing vertical separation of two traces with dual timebase plugins. 1 mA/Div sensitivity. Single Sweep Logic − 0/+5 V; high level when time-base is in single sweep mode. Single Sweep Reset − Switched to ground to reset single sweep. Aux Y Axis − Current-driven input to mainframe allowing vertical separation of two traces with dual timebase plugins. 1 mA/Div sensitivity; driven only when plug-in output is displayed (see MF Ch Switch above). Not available in early mainframes e.g. 7504, 7704 non-A. Aux Z Axis − Current-driven input to mainframe allowing plugins to modulate beam intensity, e.g. in dual timebase A intensified by B display mode; driven only when plug-in output is displayed (see MF Ch Switch above). Trigger In − Trigger signal input on H plugin, routed from V plugin's trigger output. Differential, 50 Ω per side, 50 mV/Div (differential). Aux Trigger In − Provided by 1st generation 7000 series mainframes (7704, 7504, 7503, 7403N). Only known use is in the 7B52 timebase as an optional source for the delayed trigger. Four-bay mainframes supply the trigger signal from the left horizontal bay to Aux Trig In on the right horizontal bay and vice versa, via 510 Ω resistors. Three-bay mainframes supply the Left Vert trigger signal via 510 Ω resistors. Inter-Plugin Connections − In 1st generation 7000 series mainframes (7704, 7504, 7503, 7403N), pins 26B, 27A/B and 28A/B are inter-plugin connections. In the 3-bay mainframes, right vertical slot pins 27A, 27B, 28A, 28B are connected via 50 Ω striplines to horizontal slot pins 27B, 27A, 28B, 28A respectively, with ground on 26B. Four-slot mainframes additionally make the same connections from the left vertical slot to the right horizontal slot. Since no plug-ins were made that used these connections, they were left out from later mainframes. GPIB lines − Control signal functions are the same as their IEEE-488 (GPIB) equivalents. Time slot lines 2 to 9 double as IEEE-488 data lines. TS1−TS10 − readout system time slot pulses. Idle 0, active −15 V. Force Readout − Allows plug-in readout information to be displayed regardless of the mainframe mode switch setting when pulled low (<0.5 V). Used by several 7DXX plug-ins. Plugin Mode − 5-level signal providing the mainframe with information about the operating mode of a dual-trace or dual-sweep plugin. [note 9] Ch1/2 Row/Col − Analog current inputs to the readout system. Ch1 refers to the first channel within the plugin slot in question and is associated with the readout field on top of the screen. Ch2 is the 2nd channel displayed at the bottom. Row/Current signals accept negative currents in 100 μA steps; typically, plugins contain resistors from time slot signal lines to row/current lines.

Links

Specifications

• Tektronix Specification 704, 7000-Series Plug-in to Mainframe Interface Manual, 1976
• Introduction to the 7000 Series Switching and Logic Circuits (Ken Parker, 1970
• Kahrs, Interfacing to the Tektronix 7000 series

Extenders/Sockets

• 067-0589-00 rigid extender
• 067-0616-00 flexible extender
• John Griessen's flex extender kit / Photo
• Repairing 7000-series plug-in sockets

Prototype

After it was decided that there would be a "New Generation" series of lab scopes to replace the 500 series, concept prototypes were built. Before Howard Vollum decided on the height of the New Generation plug-ins, a taller form factor was being considered. This is what it looked like:

• 

  Very Early New Generation Plug-in Prototype

• 

  Very Early New Generation Plug-in Prototype

• 

  Very Early New Generation Plug-in Prototype

• 

  Very Early New Generation Plug-in Prototype

From On the History and Environment of Tektronix page 58:

But Howard then threw another challenge to his group: plug-in height. Work up through late 1966 had assumed a seven inch plug-in height which would provide room for the needed components using readily available and proven parts. But the H-P scopes were smaller in size and quite attractive in appearance. So, one day, Howard said, "the plug-ins will be 5 1/2 inches in height."

Oliver Dalton recalls the decision to reduce the plug-in height as a traumatic one: "The decision set us back at least one year for the height decision required three major electro-mechanical component efforts in addition to the IC read-out effort: 1) new lit push-buttons ... we needed 25 on a panel; 2) cam switches - these were Howard's ideas ... we needed them to be small and reasonably cheap; 3) relays ... we needed them to be small and reliable. We then largely had to make do with other available parts, like potentiometers."