BNC connector with readout ring: Difference between revisions
No edit summary |
No edit summary |
||
(10 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
[[File:Readout_ring.jpg|thumb|250px|right]] | [[File:Readout_ring.jpg|thumb|250px|right|BNC connector with readout ring]] | ||
[[File:Readout_pin.jpg|thumb|250px|right]] | [[File:Readout_pin.jpg|thumb|250px|right|Typical readout spring contact]] | ||
[[File:Tek Pobe P6009 readout.jpg|thumb|250px|right|Different readout contact configurations of [[P6009]] probe: spring loaded pin (left) vs. spring metal clip with two contact points (right)]] | |||
Many 1970s/1980s Tektronix scopes and plugins have '''rings around the BNC input sockets''' that allow the attenuation factor of | Many 1970s/1980s Tektronix scopes and plugins have '''rings around the BNC input sockets''' that allow the attenuation factor of | ||
attached probes to be detected by the scope. | attached probes to be detected by the scope. | ||
The connector of compatible probes, e.g. [[P6056]], includes a contact pin connecting this ring. | The connector of compatible probes, e.g. [[P6056]], includes a contact pin connecting this ring. | ||
A resistor connected to ground encodes the probe attenuation | A resistor connected to ground encodes the probe attenuation (s.b). | ||
* In most [[7000-series plug-ins]], the ring interfaces with the [[7000 series readout system|readout system]]. The [[Media:Tek-plugin-readout.jpg|plug-in circuit]] uses the shift instructions in time slot 1 to implement the change of range. <br />If the probe includes an Identify switch at the tip, this connects the readout pin directly to ground, encoding the special IDENTIFY instruction in time slot 1. | * In most [[7000-series plug-ins]], the ring interfaces with the [[7000 series readout system|readout system]]. The [[Media:Tek-plugin-readout.jpg|plug-in circuit]] uses the shift instructions in time slot 1 to implement the change of range. <br />If the probe includes an Identify switch at the tip, this connects the readout pin directly to ground, encoding the special IDENTIFY instruction in time slot 1. | ||
* Readout-less [[5000-series plug-ins]] and a number of standalone scopes of the same era, e.g. many of the [[400-series scopes]] such as [[464]], use the ring to detect a ×10 (but not a ×100) probe, and indicate the correct scale factor using front-panel lamps or LEDs. The [[485]] also uses the probe ring | * [[7000-series scopes]] only display ×1, ×10 and ×100 factors. [[11000-series_scopes|11K]], [[TDS series scopes|TDS]], [[:Category:2400 series scopes|2400]] and later recognize [[P6015A|×1000]], ×2, ×5, ×200 and possibly other factors. | ||
* The [[7A14]] | * Readout-less [[5000-series plug-ins]] and a number of standalone scopes of the same era, e.g. many of the [[400-series scopes]] such as [[464]]/[[465]]/[[475]], use the ring to detect a ×10 (but not a ×100) probe, and indicate the correct scale factor [[Patent US 3725724A|using front-panel lamps or LEDs]]. The [[485]] also uses the probe ring but utilizes a TEK custom IC [[155-0076-00]] and three LEDs to indicate ×1, ×10, and ×100 probes. | ||
* The [[7A14]] plug-in uses the same BNC connector with a ring but the ring serves a different purpose, which is to detect the difference between the [[P6021]] and [[P6022]] probes, and switching in appropriate gain and frequency compensation. The P6021 (or a [[131-0750-00]] adapter for the [[P6019]]) shorts this ring to ground, directly switching three relays connected to −15 V internally. | |||
==Resistor values== | |||
''please add known nominal values where noted '(?)' '' | |||
{| class="wikitable" | |||
! Display | |||
! Resistance | |||
|- bgcolor="#F0FFF0" | |||
| ×1 || open | |||
|- | |||
| ×2 || 2.2 kΩ (?) <ref name="sciel" /> | |||
|- | |||
| ×5 || 1.8 kΩ (?) <ref name="sciel" /> | |||
|- bgcolor="#F0FFF0" | |||
| ×10 || 11 kΩ <ref name="P6056">[[Media:010-6056-03.pdf|Tektronix P6056/P6057 Manual]]</ref> | |||
|- | |||
| ×20 || 1.6 kΩ (?) <ref name="sciel" /> | |||
|- | |||
| ×50 || 1.14 kΩ <ref name="eevblog">[https://www.eevblog.com/forum/testgear/tek-p5205-hv-differeantial-probe-teardown-btw-what-are-the-red-and-brown-wires/ Tek P5205 HV differential probe teardown] @ EEVBLOG (with internal photos)</ref> | |||
|- bgcolor="#F0FFF0" | |||
| ×100 || 6.8 kΩ <ref name="P6056" /> | |||
|- | |||
| ×200 || 910 Ω (?) <ref name="sciel" /> | |||
|- | |||
| ×500 || 690 Ω <ref name="eevblog" /> | |||
|- | |||
| ×1000 || 470 Ω <ref name="sciel">[https://web.archive.org/web/20140731013321/https://www.electronics-related.com/sci.electronics.design/thread/116046/readout-pin-on-oscilloscope-probes.php sci.electronics.design thread (2009) about probe readout details]</ref> | |||
|- bgcolor="#F0FFF0" | |||
| Identify || short | |||
|} | |||
'''References''' | |||
<references /> | |||
==See also== | ==See also== | ||
* [[7000 series readout system]] | * [[7000 series readout system]] | ||
* [https://www.thingiverse.com/thing:5463077 3D model for replacing the plastic twist-on/pin holder ring on many Tek probes], e.g. [[P6105]] | * [https://www.thingiverse.com/thing:5463077 3D model for replacing the plastic twist-on/pin holder ring on many Tek probes], e.g. [[P6105]] | ||
[[Category:Probe interfaces]] | [[Category:Probe interfaces]] | ||
[[Category:Introduced in 1969]] | [[Category:Introduced in 1969]] |
Latest revision as of 03:08, 8 June 2024
Many 1970s/1980s Tektronix scopes and plugins have rings around the BNC input sockets that allow the attenuation factor of attached probes to be detected by the scope.
![](http://w140.com/tekwiki/images/thumb/e/ed/Readout_ring.jpg/250px-Readout_ring.jpg)
![](http://w140.com/tekwiki/images/thumb/f/f3/Readout_pin.jpg/250px-Readout_pin.jpg)
![](http://w140.com/tekwiki/images/thumb/d/d7/Tek_Pobe_P6009_readout.jpg/250px-Tek_Pobe_P6009_readout.jpg)
The connector of compatible probes, e.g. P6056, includes a contact pin connecting this ring. A resistor connected to ground encodes the probe attenuation (s.b).
- In most 7000-series plug-ins, the ring interfaces with the readout system. The plug-in circuit uses the shift instructions in time slot 1 to implement the change of range.
If the probe includes an Identify switch at the tip, this connects the readout pin directly to ground, encoding the special IDENTIFY instruction in time slot 1. - 7000-series scopes only display ×1, ×10 and ×100 factors. 11K, TDS, 2400 and later recognize ×1000, ×2, ×5, ×200 and possibly other factors.
- Readout-less 5000-series plug-ins and a number of standalone scopes of the same era, e.g. many of the 400-series scopes such as 464/465/475, use the ring to detect a ×10 (but not a ×100) probe, and indicate the correct scale factor using front-panel lamps or LEDs. The 485 also uses the probe ring but utilizes a TEK custom IC 155-0076-00 and three LEDs to indicate ×1, ×10, and ×100 probes.
- The 7A14 plug-in uses the same BNC connector with a ring but the ring serves a different purpose, which is to detect the difference between the P6021 and P6022 probes, and switching in appropriate gain and frequency compensation. The P6021 (or a 131-0750-00 adapter for the P6019) shorts this ring to ground, directly switching three relays connected to −15 V internally.
Resistor values
please add known nominal values where noted '(?)'
Display | Resistance |
---|---|
×1 | open |
×2 | 2.2 kΩ (?) [1] |
×5 | 1.8 kΩ (?) [1] |
×10 | 11 kΩ [2] |
×20 | 1.6 kΩ (?) [1] |
×50 | 1.14 kΩ [3] |
×100 | 6.8 kΩ [2] |
×200 | 910 Ω (?) [1] |
×500 | 690 Ω [3] |
×1000 | 470 Ω [1] |
Identify | short |
References
- ↑ 1.0 1.1 1.2 1.3 1.4 sci.electronics.design thread (2009) about probe readout details
- ↑ 2.0 2.1 Tektronix P6056/P6057 Manual
- ↑ 3.0 3.1 Tek P5205 HV differential probe teardown @ EEVBLOG (with internal photos)