7A24: Difference between revisions
No edit summary |
No edit summary |
||
(23 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
The Tektronix 7A24 is a | {{Plugin Sidebar | ||
|manufacturer=Tektronix | |||
The | |series=7000-series scopes | ||
|type=7A24 | |||
|summary=400 MHz dual channel vertical amplifier | |||
|image=7a24 front.jpg | |||
|caption=7A24 front panel | |||
|introduced=1974 | |||
|discontinued=1991 | |||
|designers=Tom Rousseau | |||
|manuals= | |||
* [[Media:070-1485-00.pdf|Tektronix 7A24 Manual]] (early version) | |||
* [[Media:070-2391-00.pdf|Tektronix 7A24 Manual]] (later version SN B103000+, OCR) | |||
}} | |||
The '''Tektronix 7A24''' is a 400 MHz dual-channel vertical plug-in for [[7000-series scopes]] with (fused) 50 Ω [[BNC]] inputs. It is the fastest multi-channel plug-in available for the 7000 series. Unlike most other plug-ins, it does not offer AC input coupling. | |||
A single-channel version was planned as the [[7A25]] but did not make it into production. | |||
The 7A24 would typically have been used in [[7834]], [[7844]] or [[7854]] mainframes. | |||
The recommended probes were the [[P6056]] and [[P6057]]. | The recommended probes were the [[P6056]] and [[P6057]]. | ||
* [ | The 75 MHz [[7A18]] and 200 MHz [[7A26]] share the same front panel layout and operation (but have 1 MΩ inputs). | ||
* [http:// | |||
{{BeginSpecs}} | |||
{{Spec | Bandwidth | 400 MHz (71xx) / 350 MHz (79xx) / 300 MHz (78xx) }} | |||
{{Spec | Deflection | 5 mV/Div to 1 V/Div (1–2–5), variable ×2.5 (up to 2.5 V/Div) }} | |||
{{Spec | Input impedance | 50 Ω }} | |||
{{Spec | Maximum input | 5 V (0.5 W) − no damage below 10 V (2 W) }} | |||
{{Spec | Timing | Delay difference between channels <200 ps }} | |||
{{EndSpecs}} | |||
==Internals== | |||
The 7A24's input attenuators are similar to that in the [[7A19]], using replaceable ceramic | |||
attenuator modules held to the switching PCB using steel springs. | |||
The amplifier is built using the Tek-made differential amplifier [[155-0078-00|155-0078-xx]] (four units per channel in early, five in late versions; various grades). | |||
In the 5 mV/Div range only, the amplifier gain is doubled electronically. | |||
The signal trace layout on the PCB is designed to provide [[T-coil peaking]]. | |||
The 7A24 does not use the ±50 V supplies provided by the mainframe. | |||
==Links== | |||
* [https://www.amplifier.cd/Test_Equipment/Tektronix/Tektronix_7000_series_amplifier/amplifier_7A24.htm Tek 7A24 page @ amplifier.cd] | |||
* [http://www.barrytech.com/tektronix/tek7000/tek7a24.html Tek 7A24 page @ barrytech.com] | |||
==Pictures== | |||
<gallery> | <gallery> | ||
Tek 7a24 1.jpg | |||
Tek 7a24 2.jpg | |||
Tek 7a24 3.jpg | |||
7a24 front.jpg | Front | |||
7a24-left.jpg | Left side (later version) | |||
7a24-right.jpg | Right side (later version) | |||
7a24 frontend.jpg | Attenuator switches | |||
7a24 left board.jpg | Amplifier board | |||
7a24 right front.jpg | Right front | |||
7a24 right rear.jpg | Right rear | |||
7a24-signal-out.jpg | [[Tektronix Cartoons|Cartoon]] in schematic: Signal Out | |||
</gallery> | </gallery> | ||
==Components== | |||
{{Parts|7A24}} | |||
[[Category:7000 series vertical plugins]] |
Revision as of 07:33, 12 December 2023
The Tektronix 7A24 is a 400 MHz dual-channel vertical plug-in for 7000-series scopes with (fused) 50 Ω BNC inputs. It is the fastest multi-channel plug-in available for the 7000 series. Unlike most other plug-ins, it does not offer AC input coupling.
A single-channel version was planned as the 7A25 but did not make it into production.
The 7A24 would typically have been used in 7834, 7844 or 7854 mainframes. The recommended probes were the P6056 and P6057.
The 75 MHz 7A18 and 200 MHz 7A26 share the same front panel layout and operation (but have 1 MΩ inputs).
Key Specifications
Bandwidth | 400 MHz (71xx) / 350 MHz (79xx) / 300 MHz (78xx) |
---|---|
Deflection | 5 mV/Div to 1 V/Div (1–2–5), variable ×2.5 (up to 2.5 V/Div) |
Input impedance | 50 Ω |
Maximum input | 5 V (0.5 W) − no damage below 10 V (2 W) |
Timing | Delay difference between channels <200 ps |
Internals
The 7A24's input attenuators are similar to that in the 7A19, using replaceable ceramic attenuator modules held to the switching PCB using steel springs.
The amplifier is built using the Tek-made differential amplifier 155-0078-xx (four units per channel in early, five in late versions; various grades). In the 5 mV/Div range only, the amplifier gain is doubled electronically. The signal trace layout on the PCB is designed to provide T-coil peaking.
The 7A24 does not use the ±50 V supplies provided by the mainframe.
Links
Pictures
-
-
-
-
Front
-
Left side (later version)
-
Right side (later version)
-
Attenuator switches
-
Amplifier board
-
Right front
-
Right rear
-
Cartoon in schematic: Signal Out
Components
Some Parts Used in the 7A24
Part | Part Number(s) | Class | Description | Used in |
---|---|---|---|---|
155-0078-00 | 155-0078-xx • 155-0273-00 • 155-0274-00 | Monolithic integrated circuit | broadband amplifier | 464 • 465 • 466 • 468 • 475 • 475A • 475M • 485 • 7834 • 7844 • 7854 • 7904 • R7903 • R7912 • 7912AD • 7912HB • 7104 • 7A16A • 7A16P • 7A24 • 7A26 • 7A42 • 067-0587-01 • 067-0680-00 • AM503 • PG502 • PG508 • DC510 • DC5010 • FG5010 |