11A34: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
 
(21 intermediate revisions by 3 users not shown)
Line 8: Line 8:
|introduced=1987  
|introduced=1987  
|discontinued=(?)  
|discontinued=(?)  
|designers=Murlan Kaufman
|designers=Murlan Kaufman;Cliff Baker
|manuals=
|manuals=
* [[Media:070-5921-01.pdf|Tektronix 11A34 User Reference -01]]
* [[Media:070-5921-01.pdf|Tektronix 11A34 User Reference -01]]
Line 15: Line 15:
* [[Media:070-7389-99.pdf|Tektronix 11A34 Extended Service Manual]]
* [[Media:070-7389-99.pdf|Tektronix 11A34 Extended Service Manual]]
* [[Media:Tektronix 11k plugin NVRAM replacement.pdf|Tektronix 11k Plug-in NVRAM Replacement]]
* [[Media:Tektronix 11k plugin NVRAM replacement.pdf|Tektronix 11k Plug-in NVRAM Replacement]]
{{ROM Images}}
}}
}}
The '''Tektronix 11A34''' is a four-channel vertical amplifier plug-in for [[11000-series_scopes|11000-series]] and DSA600-series scopes.
The '''Tektronix 11A34''' is a four-channel vertical amplifier plug-in for [[11000-series_scopes|11000-series]] and DSA600-series scopes.
Line 20: Line 21:
Option 23 added four [[P6134]] probes.
Option 23 added four [[P6134]] probes.


There is also a later version, the 11A34V introduced in 1991, for video applications.
There is also a version for video applications, the 11A34V, that was introduced in 1991 (see also [[11T5H]]).
Development of the 11A34V was managed by [[Murlan Kaufman]]. (See also [[11T5H]].) ''more Information needed''
It differs from the 11A34 only in its input impedance (75 ohms). Development of the 11A34V was managed by [[Murlan Kaufman]].
 
: ''more information about 11A34V needed''
The 11A34 uses the same firmware as the [[11A32]].
 
Each of the four channels has its own M377 amplifier.
The display outputs of the four amplifiers are combined in parallel and drive the 50 Ω impedance of the mainframe.
The same is true of the trigger outputs of the four amplifiers.
The version of the M377 used in the 11A34 has 200 Ω output impedance so that four of them in parallel create an equivalent source impedance of 50 Ω.
The amplifiers can be connected in parallel because regardless of whether the amplifier's output is enabled:
* each amplifier's output has a source impedance of 200 Ω so the four amplifiers in parallel match the 50 Ω spec of the [[11000 Series plug-in interface]].
* each amplifier's nominal common-mode output voltage is zero
* each amplifier's nominal differential output voltage is zero
See the block diagram below.


{{BeginSpecs}}
{{BeginSpecs}}
{{Spec | Bandwidth | DC to 300 MHz, 100 MHz and 20 MHz BWL filters }}
{{Spec | Bandwidth | DC to 300 MHz.  100 MHz and 20 MHz four pole BWL (Bandwidth Limit) filters may be selected.}}
{{Spec | Rise time | 1.2 ns in 1 GHz mainframe such as the [[11402]], [[11402|11402A]]. [[11403]], [[11403|11403A]], [[DSA600|DSA601A]], or [[DSA600|DSA602A]] }}
{{Spec | Rise time | 1.2 ns in 1 GHz mainframe such as the [[11402]], [[11402|11402A]], [[11403]], [[11403|11403A]], [[DSA600|DSA601A]], or [[DSA600|DSA602A]] }}
{{Spec | Deflection | 1 mV to 10 V/div in 1% calibrated steps}}
{{Spec | Deflection | 1 mV to 10 V/div in 1% calibrated steps}}
{{Spec | Input impedance | 50 Ω or 1 MΩ }}
{{Spec | Input impedance | 50 Ω or 1 MΩ }}
{{Spec | Features |
{{Spec | Features |
* High-Resolution Calibrated DC Offset
* High-resolution calibrated DC offset
* Fast Overdrive Recovery
* Fast overdrive recovery
* 50 Ω mode: 5 V RMS overload protected with manual reset
* 5 V<sub>RMS</sub> input overload protection in 50 Ω mode, with manual reset
}}
}}
{{EndSpecs}}
{{EndSpecs}}


==Links==
==Internals==
* [[11A-series plug-in NVRAM replacement]]
===Analog===
* [http://www.barrytech.com/tektronix/tek11000/tek11a34.html Tek 11A34 @ barrytech.com]
Each input channel has a separate [[119-2000-0x]] attenuator module containing passive 1 MΩ attenuators, an AC coupling capacitor,
a switch selecting the calibrator or signal input, and an [[M474]] buffer amplifier. The calibrator signal is turned off inside the plugin when not in use.
 
The attenuator module output feeds the non-inverting input of the [[M377]] amplifier IC through a (blue) 50 Ω transmission line, one per input channel.  The cable lengths set a standard delay per plugin.
 
The M377's inverting input is connected to the [[ACVS]] (Analog Control Voltage System) output.
 
The (differential) display outputs of the four amplifiers are hard-wired in parallel and drive the mainframe’s 50 Ω per side input impedance.  The same is true of the trigger outputs of the four amplifiers.
 
The version of the M377 used in the 11A34 has a 200 Ω output impedance per side so that four of them in parallel create a source impedance of 50 Ω.
 
Each M377 amplifier's nominal common-mode output voltage is zero whether enabled or not. When not enabled, each M377 differential output is exactly zero by design.
This fact is used during calibration by the plugin’s firmware to determine the mainframe’s imbalance and compensate for it during normal operation.
 
Each of the four channels has its own AUX output on dedicated pins of the plug-in interface connector:
 
{| class="wikitable" style="margin:auto"
|-
! signal name !! positive pin number !! negative pin number
|-
| AUX 1 || B38 || B37
|-
| AUX 2 || A36 || A35
|-
| AUX 3 || B32 || B33
|-
| AUX 4 || A32 || A31
|}
 
The AUX signals emerge from each M377 amplifier as differential signal with a 200 Ω source impedance per side.  
External (on the circuit board) 66.5 Ω shunt resistors on each AUX output bring this down to the 50 Ω source impedance specified by the 11k plug-in interface.
 
See also the block diagram below.


==Internals==
===Digital===
Each channel's attenuator module contains an [[M474]] buffer amplifier.
The 11A34 and the [[11A32]] use exactly the same firmware.
Each of the attenuator modules drives an [[M377]] amplifier IC.


The [[11A32]] and 11A34 were originally intended to use [[Intel 8052]] microcontrollers.  
The [[11A32]] and 11A34 were originally intended to use [[Intel 8052]] microcontrollers.  
However, during development, the firmware swelled beyond that chip's 8192-byte maximum on-chip ROM size.  
However, during development, the firmware swelled beyond that chip's 8192-byte maximum on-chip  
[[Doug Haines]] found an alternate supplier of 8051-compatible chips (OKI Semiconductor) that offered a 16Kbyte on-chip ROM,  
ROM size. [[Doug Haines]] found an alternate supplier of 8051-compatible chips (OKI Semiconductor) that offered a 16 KByte on-chip ROM, and that's what the plug-ins wound up with. The finished code size is about 14 KB.
and that's what the plug-ins wound up with. The finished code size wound up at about 14 KB.
 
The 11A34 also contains a Dallas Semiconductor DS1220Y NVRAM storing last settings, calibration constants, and instrument serial number. 
The DS1220Y contains a battery with a typical life time of 20-30 years. 
 
There are also two [[ACVS]] (Analog Control Voltage System) sample and hold modules on two daughter boards that generate the analog voltages needed for gain and offset, including error correction under microcontroller firmware control. 


The 11A34 contains two [[ACVS]] sample and hold modules.
The microcontroller also provides the digital signals sent to the M377 amplifier, setting one of its six fixed gains, one of its three bandwidths, turning on or off its selected output, and each output's + up or invert state.
 
Digital mainframes do waveform manipulation (addition, subtraction, multiplication, etc.).  Consequently only one 11A34 output is on at a time.  Analog mainframes however allow more than one channel to be on at a time.  This allows the plugin channels to be added or subtracted in the plugin.
 
==Links==
* [[11A-series plug-in NVRAM replacement]]
{{Documents|Link=11A34}}
{{PatentLinks|11A34}}


==Pictures==
==Pictures==
<gallery>
<gallery>
Tek 11a34 front.jpg
Tek 11a34 front.jpg | 11A34 front view
11a34_front.jpg|front view
11a34_front.jpg|front view
11a34_left2.jpg|left side view
11a34_left2.jpg|left side view
Line 70: Line 102:
11a34_bottom.jpg|bottom view
11a34_bottom.jpg|bottom view
Tek 11a34 block diagram.png|Block diagram
Tek 11a34 block diagram.png|Block diagram
Tek 11a34 input attenuators.jpg|Input Attenuators
Tek 11a34 kernel.jpg|Kernel
Tek 11A34 analog control and signal amplifiers.png|Analog Control and Signal Amplifiers
Tek 11a34 main interface.jpg|Main Interface
Tek_11a34v_and_11t5h.jpg|11A34V and 11T5H
Tek_11a34v_and_11t5h.jpg|11A34V and 11T5H
Tek_11a34v_and_11t5h_2.jpg|11A34V and 11T5H
Tek_11a34v_and_11t5h_2.jpg|11A34V and 11T5H
Line 83: Line 119:
</gallery>
</gallery>


{{Custom ICs|11A34}}
==Parts==
{{Parts|11A34}}


[[Category:11000 series plugins]]
[[Category:11000 series plugins]]
[[Category:Tekprobe BNC]]
[[Category:Tekprobe BNC]]

Latest revision as of 09:22, 22 September 2024

Tektronix 11A34
Quad channel 300 MHz amplifier
Tek 11A34

Compatible with 11000-series scopes

Produced from 1987 to (?)

Manuals
ROM Images
File Pos. Checksum
160-4009-04 U700 3e2de25b
160-4009-08 U700 8c2d1027
(All manuals in PDF format unless noted otherwise)
Manuals – Specifications – Links – Pictures

The Tektronix 11A34 is a four-channel vertical amplifier plug-in for 11000-series and DSA600-series scopes.

Option 23 added four P6134 probes.

There is also a version for video applications, the 11A34V, that was introduced in 1991 (see also 11T5H). It differs from the 11A34 only in its input impedance (75 ohms). Development of the 11A34V was managed by Murlan Kaufman.

more information about 11A34V needed

Key Specifications

Bandwidth DC to 300 MHz. 100 MHz and 20 MHz four pole BWL (Bandwidth Limit) filters may be selected.
Rise time 1.2 ns in 1 GHz mainframe such as the 11402, 11402A, 11403, 11403A, DSA601A, or DSA602A
Deflection 1 mV to 10 V/div in 1% calibrated steps
Input impedance 50 Ω or 1 MΩ
Features
  • High-resolution calibrated DC offset
  • Fast overdrive recovery
  • 5 VRMS input overload protection in 50 Ω mode, with manual reset

Internals

Analog

Each input channel has a separate 119-2000-0x attenuator module containing passive 1 MΩ attenuators, an AC coupling capacitor, a switch selecting the calibrator or signal input, and an M474 buffer amplifier. The calibrator signal is turned off inside the plugin when not in use.

The attenuator module output feeds the non-inverting input of the M377 amplifier IC through a (blue) 50 Ω transmission line, one per input channel. The cable lengths set a standard delay per plugin.

The M377's inverting input is connected to the ACVS (Analog Control Voltage System) output.

The (differential) display outputs of the four amplifiers are hard-wired in parallel and drive the mainframe’s 50 Ω per side input impedance. The same is true of the trigger outputs of the four amplifiers.

The version of the M377 used in the 11A34 has a 200 Ω output impedance per side so that four of them in parallel create a source impedance of 50 Ω.

Each M377 amplifier's nominal common-mode output voltage is zero whether enabled or not. When not enabled, each M377 differential output is exactly zero by design. This fact is used during calibration by the plugin’s firmware to determine the mainframe’s imbalance and compensate for it during normal operation.

Each of the four channels has its own AUX output on dedicated pins of the plug-in interface connector:

signal name positive pin number negative pin number
AUX 1 B38 B37
AUX 2 A36 A35
AUX 3 B32 B33
AUX 4 A32 A31

The AUX signals emerge from each M377 amplifier as differential signal with a 200 Ω source impedance per side. External (on the circuit board) 66.5 Ω shunt resistors on each AUX output bring this down to the 50 Ω source impedance specified by the 11k plug-in interface.

See also the block diagram below.

Digital

The 11A34 and the 11A32 use exactly the same firmware.

The 11A32 and 11A34 were originally intended to use Intel 8052 microcontrollers. However, during development, the firmware swelled beyond that chip's 8192-byte maximum on-chip ROM size. Doug Haines found an alternate supplier of 8051-compatible chips (OKI Semiconductor) that offered a 16 KByte on-chip ROM, and that's what the plug-ins wound up with. The finished code size is about 14 KB.

The 11A34 also contains a Dallas Semiconductor DS1220Y NVRAM storing last settings, calibration constants, and instrument serial number. The DS1220Y contains a battery with a typical life time of 20-30 years.

There are also two ACVS (Analog Control Voltage System) sample and hold modules on two daughter boards that generate the analog voltages needed for gain and offset, including error correction under microcontroller firmware control.

The microcontroller also provides the digital signals sent to the M377 amplifier, setting one of its six fixed gains, one of its three bandwidths, turning on or off its selected output, and each output's + up or invert state.

Digital mainframes do waveform manipulation (addition, subtraction, multiplication, etc.). Consequently only one 11A34 output is on at a time. Analog mainframes however allow more than one channel to be on at a time. This allows the plugin channels to be added or subtracted in the plugin.

Links

Documents Referencing 11A34

Document Class Title Authors Year Links
Electronic-Engineering-Aug-Sept-1988-Versatile-Analogue-Chip-John-Addis.pdf Article Versatile Analogue Chip for Oscilloscope Plug-ins John Addis 1988 M377 • 11A32 • 11A33 • 11A34 • 11A52 • Cascomp • Overdrive • Thermals • Gilbert multiplier • Pat Quinn • Gary Polhemus • Art Metz

Pictures

  • 11A34 front view

    11A34 front view

  • front view

    front view

  • left side view

    left side view

  • right side view

    right side view

  • bottom view

    bottom view

  • Block diagram

    Block diagram

  • Input Attenuators

    Input Attenuators

  • Kernel

    Kernel

  • Analog Control and Signal Amplifiers

    Analog Control and Signal Amplifiers

  • Main Interface

    Main Interface

  • 11A34V and 11T5H

    11A34V and 11T5H

  • 11A34V and 11T5H

    11A34V and 11T5H

  • Prototype 11A34

    Prototype 11A34

  • Prototype 11A34

    Prototype 11A34

  • Prototype 11A34

    Prototype 11A34

  • Prototype 11A34

    Prototype 11A34

  • 11A34V front

    11A34V front

  • 11A34V rear

    11A34V rear

  • 11A34V left internal

    11A34V left internal

  • 11A34V right internal

    11A34V right internal

  • 11A34

    11A34

Parts

Some Parts Used in the 11A34

Part Part Number(s) Class Description Used in
Intel 8051 Monolithic integrated circuit 8-bit microcontroller 11A32 • 11A34 • WFM300
M377 165-2129-03 • 165-2089-06 • 155-2089-05 Monolithic integrated circuit amplifier 11A16 • 11A32 • 11A33 • 11A34 • 11A52 • 2245 • 2245A • 2247 • 2247A • 2252 • TDS410 • TDS420 • TDS460 • TDS520D • TDS540D • TDS580D • TDS680C • TDS684C • TDS714L • TDS724D • TDS754D • TDS784D
M474 Monolithic integrated circuit amplifier 11A32 • 11A34
Retrieved from "https://w140.com/tekwiki/index.php?title=11A34&oldid=97382"