514: Difference between revisions
mNo edit summary |
No edit summary |
||
Line 10: | Line 10: | ||
|designers=Dick Rhiger | |designers=Dick Rhiger | ||
|manuals= | |manuals= | ||
* [ | * [[Media:IM-514D.pdf|Tektronix 514D Manual]] | ||
* [[Media:Tek 514 history parts list.pdf|Tektronix 514 History Parts List | * [[Media:Tek 514 history parts list.pdf|Tektronix 514 History Parts List]] | ||
}} | }} | ||
The '''Tektronix 514''' is a monolithic general-purpose oscilloscope introduced in 1949 or 1950. | The '''Tektronix 514''' is a monolithic general-purpose oscilloscope introduced in 1949 or 1950. |
Revision as of 06:58, 28 April 2023
The Tektronix 514 is a monolithic general-purpose oscilloscope introduced in 1949 or 1950.
It was designed by Tektronix engineers Bob Davis and Dick Rhiger.
Using a three-section distributed amplifier, it provides frequency response from DC to 10 MHz. Prior to the 514, customers had to choose between an instrument with 10 MHz bandwidth (the 511) or an instrument with DC–2 MHz response (the 512). The 514 provides DC response and 10 MHz bandwidth.
Throughout its production run, a 'D' variant was available (514D, with the 'D' being stamped in by hand on some models), which has a 24-section 250 ns lumped L-C delay line. There was also an 'A' version (514-A & 514-AD respectively), which appears to have been available in 1954. (There were also some models marked 'Series A', which may have been a predecessor to the 514A? How does the 514AD differ from the 514D?)
It has no thermal cutoff.
Key Specifications
Frequency response | DC to 10 MHz |
---|---|
Input impedance | 1 MΩ // 30 pF |
Vertical deflection | 100 V/cm down to 300 mV/cm (DC) / 30 mV/cm (AC), 1–3–10 sequence |
Weight | 28.1 kg (62 pounds) |
Power consumption | 375 W |
Internals
The 514 uses a 5CPA CRT with a total accelerating voltage of 3 kV (−1.5 kV on the CRT cathode and +1.5 kV on the CRT anode). The standard phosphor for a 514 was P1. The deflection sensitivity of the CRT is approximately 27 V/cm vertical and 32 V/cm horizontal.
The power supply is regulated based on a −140 V reference produced by an OD3 gas regulator tube. The +225 V supply uses three 5V4G rectifier tubes in parallel.
Links
Pictures
514
-
Front
-
514AD with B&K Curve Tracer
-
Distributed vertical amp
-
Delay line trimmer caps
-
Bottom view
-
Power Supply
-
Upper Deck, rear
-
Upper Deck, front
-
Lower Deck, front
-
Lower Deck, rear
-
Fan Motor
-
Line Socket
-
Vertical amp schematic
-
Vertical preamp, early
-
HV Power Supply, early
514AD
Some Parts Used in the 514
Part | Part Number(s) | Class | Description | Used in |
---|---|---|---|---|
0D3 | 154-003 • 154-0003-00 | Gas Discharge Tube (Voltage regulator) | 153 V voltage reference | 511 • 511A • 513 • 514 |
12AT7 | 154-0039-00 | Vacuum Tube (Dual Triode) | dual high-gain triode | 161 • 180 • 310 • 310A • 315 • 316 • 360 • 502 • 502A • 511A • 512 • 513 • 513D • 514 • 514AD • 514D • 516 • 524 • 529 • RM529 • 544 • 546 • 547 • 556 • 565 • 570 • 3A2 • 75 • 3A75 • 1M1 • A • B • C • G • H • K • L • ML • M • N • K • R • S • Z |
5CPA | 154-0063-00 | CRT | 5" CRT with electrostatic deflection | 512 • 514 |
5V4G | 154-008 • 154-0008-00 | Vacuum Tube (Dual Rectifier) | dual rectifier | 104 • 104A • 160 • 511A • 514 |
6AG7 | 154-012 • 154-0012-00 | Vacuum Tube (Pentode) | 9 Watt power pentode | 104 • 104A • 105 • 112 • 511 • 511A • 512 • 513 • 514 • 517 • 517A • 524 |
6DK6 | 154-0149-00 • 154-0367-00 | Vacuum Tube (Pentode) | high-frequency miniature pentode | 180 • 503 • 513 • 514 • 541 • 543 • 535 • 545 • 545A • 551 • 555 |