647A: Difference between revisions

Revision as of 04:36, 1 November 2023

Tektronix 647A
100 MHz scope 647A front view Produced from 1967 to 1974 Manuals Tek 647A Instruction Manual Alternate: DjVu @ BAMA R647A Manual 070-0627-00 needed Tektronix 647A Factory Calibration Procedure, February 1967 Tektronix Type 647 and 647A Calibration Outline (OCR) (All manuals in PDF format unless noted otherwise)

Manuals – Specifications – Links – Pictures

The Tektronix 647A is an improved version of the 647, with the main enhancement being doubling the bandwidth to 100 MHz.

Tek also introduced two new plug-ins with the 647A. The 10A2A is an improved version of the dual channel 10A2 vertical plug-in, with bandwidth extended to 100 MHz. The 11B2A is similar to the 11B2 dual time base, but triggers up to 100 MHz. The 10A1 differential comparator amplifier, first introduced in 1965 for the 647, has a maximum bandwidth of 55 MHz for sensitivities of 5 mV/div and higher in the 647A. It operates down to 1 mV/div sensitivity, and includes a comparison voltage mode with a calibrated DC offset similar to that first offered in the type W plug-in.

In total, only six plug-ins were developed for the 647 series – the generic dual trace vertical 10A2 and 10A2A amplifiers, a differential comparator vertical 10A1 amplifier, and a single 11B1 and dual 11B2 and 11B2A time bases. Although it combined high performance with rugged reliability and compactness, the 647 series was one of Tek’s “orphan” scope series, a result of when it was introduced. By the time the 100 MHz 647A was announced, the majority of the R&D effort at Tek was devoted to the 7000 series, which introduced just two years later, in 1969.

The entry level 7000 series mainframe started with performance nearly the same as the top of the line 647A. With on-screen scale factor read-out, and even more compact form factor, 7000 would offer many advantages over any of Tek’s existing lines of scopes. When the work on developing plug-ins for 7000 series was ramping up, no additional plug-ins for any of the “legacy” plug-in scopes would be developed. For the 530/540/550 series which started over 20 years earlier, a large family of plug-ins were available, but for scopes which were introduced in the mid 1960s, the variety of plug-ins was very limited.

The 067-0544-00 is a calibration plug-in for the 647A.

Key Specifications

Bandwidth	DC to 100 MHz (≤ 3 dB) with 10A2A plug-in
Rise time	3.5 ns
CRT	T6470, P31 std / P11 opt., 6 cm × 10 cm, 14 kV acceleration
Power	108/115/122/216/235/244 V_AC ±10%,selected via primary voltage selector and voltage range selector switches, 50 Hz to 60 Hz; 185W with 10A2 & 11B2 plug-in
Operating Temperature	–30 C° to +65 C°
Cooling	AC Fan (only in rack variant)
Thermal Protection	Automatic resetting thermal cutout, in case internal temperature exceeds safe operating level
Weight	18.4 kg (40.5 lbs)

Internals

The vertical amplifier contained in the 647A indicator unit (mainframe) consists of NPN and PNP bipolar transistors. The output transistors, Q484 and Q494, are selected 2N3866 NPN transistors. The datasheet for the 2N3866 lists Its transit frequency as 800 MHz and specifies an absolute maximum value of Vceo of 30 V. The quiescent value of Vce on Q484 and Q494 is about 30 V. So it seems likely that the selection process for these transistors involved testing their performance at the high end of their specified voltage range, and probably beyond.

The power supply of the 647A is all solid state, with a zener voltage reference and NPN pass transistors. The horizontal amplifier in the 647A uses selected 2N3119 NPN bipolar transistors for the output. These are specified as having a transit frequency of 250 MHz and a Vceo max of 80 V.

Pictures

647A front view
647A left view
647A right view
647A rear view
R647A front view
R647 inside view
Special R647A for US Air Force
Rear panel of the Air Force R647A
647A with 10A2A and 11B2A

R647A

R647A front view
RM647 inside view
Special R647A for US Air Force
Rear panel of the Air Force R647A

Components

Some Parts Used in the 647A

Part	Part Number(s)	Class	Description	Used in
2N3119	151-0124-00	Discrete component	NPN VHF power transistor	647A
2N3866	151-0211-00	Discrete component	NPN VHF power transistor	647A
5642	154-0051-00 • 154-0079-00	Vacuum Tube (Diode)	directly-heated high-voltage rectifier	310 • 310A • 316 • 317 • 360 • 453 • 502 • 502A • 503 • 504 • 506 • 513 • 515 • 516 • 524 • 529 • RM529 • 533 • 533A • 535 • 536 • 543 • 543A • 543B • 545 • 545A • 545B • 547 • 551 • 555 • 556 • 560 • 561 • 561A • 561S • 564 • 567 • 570 • 575 • 581 • 581A • 585 • 585A • 647 • 647A
T6470	154-0434-00 • 154-0448-00	CRT	CRT	647 • 647A

@@ Line 38: / Line 38: @@
 {{Spec | Bandwidth             | DC to 100 MHz (≤ 3 dB) with [[10A2A|10A2A plug-in]]  }}
 {{Spec | Rise time             | 3.5 ns }}
-{{Spec | CRT                   | 6 cm × 10 cm, 14 kV acceleration }}
+{{Spec | CRT                   | [[T6470]], P31 std / P11 opt., 6 cm × 10 cm, 14 kV acceleration }}
 {{Spec | Power                 | 108/115/122/216/235/244 V<sub>AC</sub> ±10%,selected via primary voltage selector and voltage range selector switches, 50 Hz to 60 Hz; 185W with [[10A2]] & [[11B2]]  plug-in }}
 {{Spec | Operating Temperature | –30 C° to +65 C°}}