D

The Tektronix Type D is a differential amplifier plug-in for 500-series scopes. It was designed by Rodgers Jenkins.

Manuals – Specifications – Links – Pictures

Type D was the most sensitive plug-in of the original four. The bandwidth depends on the gain, ranging from 2 MHz at 50 mV/div to 300 kHz at 1 mV/div. There are two axes of sensitivity setting: a decade attenuator in front of a gain switch. This scheme would be reprised in Type W.

It displays the difference between two input signals, with a common-mode rejection ratio of 10,000. It has six tubes, on a shock-mounted subchassis to avoid microphonics.

Along with Types A, B, and C, Type D was introduced with the 531 and 535 in 1954.

At the time it was called Type 53D. It was briefly renamed 53D/54D in 1955 with the introduction of the 541 and 545. This quickly changed to 53/54D, and finally shortened to just "D" in 1959 with the introduction of the 5xxA scopes. Its final year in the catalog was 1968; it had been superseded by Type 1A6.

K, L, and T are tied for longest production life, at 16 years. B, D, and G are next at 15 years.

Lavoie Laboratories produced an unauthorized clone, the Lavoie LA-265-D.

Key Specifications

Deflection	1 mV/Div to 50 V/Div in 1–2–5-10-20-50 sequence and 1-10-100-1000 sequence
Input impedance	1 MΩ // 47 pF (either input)
Bandwidth	2 MHz with MV/CM MULTIPLIER set to 50; 300kHz with MV/CM MULTIPLIER set to 1
CMRR	10000:1 with MILLIVOLTS/CM set to 1, 1000:1 otherwise
Signal ranges

Range	Common mode dynamic range*
MILLIVOLTS/CM = 1	±2.5 V
MILLIVOLTS/CM = 10	±25 V
MILLIVOLTS/CM = 100	±250 V
MILLIVOLTS/CM = 1000	±500 V

• In practice, Type D behaves well up to about +/–15V if the CM signal is either a brief excursion or a constant. If the CM varies slowly, DC shift in the input tubes will degrade CMRR.

Links

Documents Referencing D

Document	Class	Title	Authors	Year	Links
IBM 223-6725-2.pdf	Application Note	Tektronix oscilloscopes (IBM Customer Engineering Manual)		1960	310 • 310A • 531 • 531A • 535 • 535A • 545A • B • C • CA • D • G
Tekscope 1972 V4 N5 Sep 1972.pdf	Article	A Practical Approach to Differential Amplifiers and Measurements	Fred Beckett	1972	112 • 11A33 • 1A5 • 1A6 • 1A7 • 1A7A • 26A2 • 3A9 • 5A22N • 7A13 • 7A22 • AM502 • D • E • G • P6055 • P6046 • W • Z
Tekscope 1972 V4 N6 Nov 1972.pdf	Article	Differential Amplifiers and Measurements, Part 2	Fred Beckett	1972	112 • 11A33 • 1A5 • 1A6 • 1A7 • 1A7A • 26A2 • 3A9 • 5A22N • 7A13 • 7A22 • AM502 • D • E • G • P6055 • P6046 • W • Z

Internals

Instruments below serial number 3462 used a pair of 5814 tubes at the input; later production used 12AU7's. These two tube types have different heater currents, and because the heaters are series-wired, you cannot switch from one type to the other without circuit modification.

Pictures

• 
• 

  Front

• 

  Chassis

• 

  Rubber support for elimination of microphonics

• 

  Chassis bottom

• 

  Early Schematic

• 

  Late Schematic

• 

  Late Attenuators

• 

  Front View (vertical position knob not original)

Components