7A22: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
mNo edit summary
 
(6 intermediate revisions by the same user not shown)
Line 10: Line 10:
|designers=Val Garuts
|designers=Val Garuts
|manuals=
|manuals=
* [[Media:070-0931-00.pdf|Tektronix 7A22 Manual]] (PDF, OCR)
* [[Media:070-0931-00.pdf|Tektronix 7A22 Manual]] (OCR)
* [http://bama.edebris.com/download/tek/7a22(2)/tek-7a22.pdf Tektronix 7A22 Manual @ BAMA] (PDF)
* [http://bama.edebris.com/download/tek/7a22(2)/tek-7a22.pdf Tektronix 7A22 Manual @ BAMA]
* [[Media:TM-11-6625-2749-14&P.pdf| TM-11-6625-2749-14&P - 7A22 military manual]] (PDF, 8M)
* [[Media:TM-11-6625-2749-14&P.pdf| TM-11-6625-2749-14&P - 7A22 military manual]]
* [[Media:TB-9-6625-2132-35.pdf | TB 9-6625-2132-35 Calibration Procedure for AM-6881/U (7A13) and AM-6786/U (7A22)]] (PDF, 2M)
* [[Media:TB-9-6625-2132-35.pdf | TB 9-6625-2132-35 Calibration Procedure for AM-6881/U (7A13) and AM-6786/U (7A22)]]
}}
}}
The '''Tektronix 7A22''' is a single channel differential vertical amplifier for the [[7000-series scopes|7000 series mainframes]], designed by [[Val Garuts]] and produced from about 1969 to 1991.  Specifications and controls are similar to the [[26A2]] and the [[3A9]] from the 560 series but without current probe input or front panel signal output.
The '''Tektronix 7A22''' is a single channel differential vertical amplifier for the [[7000-series scopes|7000 series mainframes]], designed by [[Val Garuts]] and produced from about 1969 to 1991.  Specifications and controls are similar to the [[26A2]] and the [[3A9]] from the 560 series but without current probe input nor front panel signal output.


Remarkably, the 7A22's input sensitivity reaches down to 10 μV/Div.  Bandwidth is 1 MHz, the upper 3 dB limit can be reduced in ×3 steps down to 100 Hz (to eliminate noise, inter alia), and the lower bandwidth can be raised in ×10 steps from 0.1 Hz to 10 kHz.  A separate control optionally supplies an internal DC voltage to offset the DC signal component.  Even in the most sensitive ranges (10 μV/Div to 10 mV/Div), common-mode voltage can be ±10 V.  Input resistance is 1 MΩ, but for high source resistance DC coupled measurements, one can disconnect the internal gate return resistors of the input FETs, at the disadvantage of disabling the 20 mV/div and higher ranges.
The 7A22's input sensitivity reaches down to 10 μV/Div.  Bandwidth is 1 MHz, the upper 3 dB limit can be reduced in ×3 steps down to 100 Hz (to eliminate noise, inter alia), and the lower bandwidth can be raised in ×10 steps from 0.1 Hz to 10 kHz.  A separate control optionally supplies an internal DC voltage to offset the DC signal component.  Even in the most sensitive ranges (10 μV/Div to 10 mV/Div), common-mode voltage can be ±10 V.  Input resistance is 1 MΩ, but for high source resistance DC coupled measurements, one can disconnect the internal gate return resistors of the input FETs, at the disadvantage of disabling the 20 mV/div and higher ranges.


Applications include audio, biological signals, sensors etc.
Applications include audio, biological signals, sensors etc.
Line 44: Line 44:
|}
|}
{{EndSpecs}}
{{EndSpecs}}
==Links==
{{Documents|Link=7A22}}


==Internals==
==Internals==
The differential amplifier design is a variant of the [[1A7A]] circuit, also used with modifications in the [[3A9]], [[5A22N]], [[AM502]], and [[5030]]/[[5031]] ([[26A2]] too?).
The differential amplifier design is a variant of the [[1A7A]] circuit, also used with modifications in the [[3A9]], [[5A22N]], [[AM502]], and [[5030]]/[[5031]] ([[26A2]] too?).


The 7A22 uses the ±50 V supplies provided by the mainframe.
<blockquote>
[[John Addis]] [[Preamble DA1855|says]]:
 
The [[1A7A]] (designed by [[Thor Hallen]]) and the 7A22 (designed by [[Val Garuts]]) used essentially the same circuit. Exactly who came up with the brilliant input circuit is lost to history. The 1A7A came out first, but Thor had worked as evaluation engineer for Val Garuts. Val does not remember who created the circuit, and Thor died in 2002.
</blockquote>


==Prices==
==Prices==
Line 67: Line 74:
|align=right| $2,260
|align=right| $2,260
|-
|-
! 2018 value
! In 2023 Dollars
|align=right| $3,240
|align=right| $3,900
|align=right| $3,110
|align=right| $3,800
|align=right| $3,240
|align=right| $3,900
|align=right| $3,850
|align=right| $4,700
|align=right| $4,350
|align=right| $5,300
|-
|-
|}
|}
Line 80: Line 87:
===Plug-in===
===Plug-in===
<gallery>
<gallery>
Tek 7a22 5.jpg
Tek 7a22 front.jpg | 7A22 front view
Tek 7a22 front.jpg | 7A22 front view
Tek-7a22-front.jpg
Tek-7a22-front.jpg
Tek 7a22 5.jpg
Tek 7a22 front2.jpg
7a22-left.jpg      | left side
7a22-left.jpg      | left side
7a22-left-ext.jpg  | left side (with cover)
7a22-left-ext.jpg  | left side (with cover)

Latest revision as of 23:26, 19 May 2024

Tektronix 7A22
1 MHz differential amplifier
7A22 front view

Compatible with 7000-series scopes

Produced from 1969 to 1991

Manuals
Manuals – Specifications – Links – Pictures

The Tektronix 7A22 is a single channel differential vertical amplifier for the 7000 series mainframes, designed by Val Garuts and produced from about 1969 to 1991. Specifications and controls are similar to the 26A2 and the 3A9 from the 560 series but without current probe input nor front panel signal output.

The 7A22's input sensitivity reaches down to 10 μV/Div. Bandwidth is 1 MHz, the upper 3 dB limit can be reduced in ×3 steps down to 100 Hz (to eliminate noise, inter alia), and the lower bandwidth can be raised in ×10 steps from 0.1 Hz to 10 kHz. A separate control optionally supplies an internal DC voltage to offset the DC signal component. Even in the most sensitive ranges (10 μV/Div to 10 mV/Div), common-mode voltage can be ±10 V. Input resistance is 1 MΩ, but for high source resistance DC coupled measurements, one can disconnect the internal gate return resistors of the input FETs, at the disadvantage of disabling the 20 mV/div and higher ranges.

Applications include audio, biological signals, sensors etc.

An example application is found in Jim Williams' LT Application Note 124 – see Appendix D for a comparison of differential amplifiers.

Key Specifications

Bandwidth 1 MHz, LF limit switchable DC, 0.1 Hz to 10 kHz in ×10 steps, HF limit switchable 100 Hz to 1 MHz in ×3/×10 steps
Deflection 10 μV/Div to 10 V/Div in 1–2–5 sequence
Input impedance 1 MΩ // 47 pF (either input)
Signal ranges
Range Differential signal DC Offset Common mode
10 μV/Div to 10 mV/Div ±1 V ±1 V ±10 V
20 mV/Div to 0.1 V/Div ±10 V ±10 V ±100 V
0.2 V/Div to 1 V/Div ±100 V ±100 V ±500 V
2 V/Div to 10 V/Div ±1000 V ±1000 V ±500 V

Links

Documents Referencing 7A22

Document Class Title Authors Year Links
Tekscope 1969 V1 N5 Oct 1969.pdf Article Introducing the New Generation 1969
Tekscope 1969 V1 N6 Dec 1969.pdf Article A New Logic for Oscilloscope Displays 1969
Tekscope 1971 V3 N2.pdf Article Measuring the Linearity of Fast Ramps John McCormick 1971
Tekscope 1972 V4 N5 Sep 1972.pdf Article A Practical Approach to Differential Amplifiers and Measurements Fred Beckett 1972
Tekscope 1972 V4 N6 Nov 1972.pdf Article Differential Amplifiers and Measurements, Part 2 Fred Beckett 1972

Internals

The differential amplifier design is a variant of the 1A7A circuit, also used with modifications in the 3A9, 5A22N, AM502, and 5030/5031 (26A2 too?).

John Addis says:

The 1A7A (designed by Thor Hallen) and the 7A22 (designed by Val Garuts) used essentially the same circuit. Exactly who came up with the brilliant input circuit is lost to history. The 1A7A came out first, but Thor had worked as evaluation engineer for Val Garuts. Val does not remember who created the circuit, and Thor died in 2002.

Prices

Year 1970 1971 1980 1984 1990
Catalog price $500 $500 $1,060 $1,590 $2,260
In 2023 Dollars $3,900 $3,800 $3,900 $4,700 $5,300

Pictures

Plug-in

Measurements