155-0078-00: Difference between revisions
No edit summary |
No edit summary |
||
(8 intermediate revisions by the same user not shown) | |||
Line 2: | Line 2: | ||
|Manufacturer=Tektronix | |Manufacturer=Tektronix | ||
|Model=M084 | |Model=M084 | ||
|Part_nos=155-0078-xx | |Part_nos=155-0078-xx,155-0273-00,155-0274-00 | ||
|Description=broadband | |Description=broadband amplifier | ||
|Used_in=475;485;7834;7844;7854;7904;R7903;7912AD;7912HB;7A16A;7A16P;7A24;7A26;7A42;067-0587-01;AM503;PG502;PG508;DC510 | |Used_in=464;465;466;468;475;475A;475M;485;7834;7844;7854;7904;R7903;R7912;7912AD;7912HB;7104;7A16A;7A16P;7A24;7A26;7A42;067-0587-01;067-0680-00;AM503;PG502;PG508;DC510;DC5010;FG5010 | ||
|Designers=John Addis; | |Designers=John Addis; | ||
}} in a [[minipac]] package. | }} in a [[minipac]] package. | ||
Line 54: | Line 54: | ||
Suffixes -10, -11, -12 and -13 were used for the redesigned M84, known as the [[M705]]. | Suffixes -10, -11, -12 and -13 were used for the redesigned M84, known as the [[M705]]. | ||
The M705 was necessary because the original [[SH2]] (2-2. | The M705 was necessary because the original [[SH2]] (2-2.5 GHz?) process was being discontinued. | ||
The M705 was designed by [[Hal | The M705 was designed by [[Hal Lillywhite]] using the faster [[SH3]] process (6-7 GHz). | ||
Additionally, the M705 apparently had the gain setting resistor laser trimmed at the wafer level. | Additionally, the M705 apparently had the gain setting resistor laser trimmed at the wafer level. | ||
The M705 was designed in late 1989 and tested in early 1990. | The M705 was designed in late 1989 and tested in early 1990. | ||
Line 115: | Line 115: | ||
* [[Media:Tek m84.pdf|Tektronix M84 155-0078-00 Description (PDF)]] | * [[Media:Tek m84.pdf|Tektronix M84 155-0078-00 Description (PDF)]] | ||
==See also== | |||
* [[234-0203-20]]: [[SH3]] version | |||
{{PatentLinks|155-0078-00}} | |||
==Pictures== | ==Pictures== | ||
Line 126: | Line 130: | ||
==Used in== | ==Used in== | ||
* [[475]] (U140, U240, U450) | * [[464]], [[465]], [[466]], [[468]] | ||
* [[475]] (U140, U240, U450), [[475A]], [[475M]] | |||
* [[485]] | * [[485]] | ||
* [[2220]], [[2221]], [[2230]] (155-0274-00: A1U130, A1U180; 155-0273-00: A2U30, A2U80) | * [[2220]], [[2221]], [[2230]] (155-0274-00: A1U130, A1U180; 155-0273-00: A2U30, A2U80) | ||
Line 132: | Line 137: | ||
* [[7854]] (A13U520,A13U590,A13U620,A13U680) | * [[7854]] (A13U520,A13U590,A13U620,A13U680) | ||
* [[7904]], [[R7903]] (U5510,U5530,U5550,U5610,U5630,U5650) | * [[7904]], [[R7903]] (U5510,U5530,U5550,U5610,U5630,U5650) | ||
* [[7912AD]], [[7912HB]] | * [[R7912]], [[7912AD]], [[7912HB]] | ||
* [[7A16A]] (U350, U450, U550, U750) | * [[7104]] | ||
* [[7A16A]] (U350, U450, U550, U750), [[7A16P]] (U60240, U60340, U60440, U60540) | |||
* [[7A24]], [[7A26]] (U1350,U1450,U1550,U1750,U2350,U2450,U2550,U2750) | * [[7A24]], [[7A26]] (U1350,U1450,U1550,U1750,U2350,U2450,U2550,U2750) | ||
* [[7A26]] | |||
* [[7A42]] (A5U1010,A5U1020,A5U1040,A5U1060) | * [[7A42]] (A5U1010,A5U1020,A5U1040,A5U1060) | ||
* [[067-0587-01]] | * [[067-0587-01]], [[067-0680-00]] | ||
* [[AM503]] | * [[AM503]] | ||
* [[PG502]] (U360, -06) | * [[PG502]] (U360, -06) | ||
* [[PG508]] (U850) | * [[PG508]] (U850) | ||
* [[DC510]] (A12U1311, A12U1331, -10) | * [[DC510]] (A12U1311, A12U1331, -10), [[DC5010]] | ||
* [[FG5010]] | |||
{{Part usage}} | |||
==Notes== | ==Notes== |
Latest revision as of 04:28, 8 June 2024
The Tektronix M084 (P/N 155-0078-xx,155-0273-00,155-0274-00) is a broadband amplifier monolithic integrated circuit in a minipac package. The input and output are differential. The 155-0078 and its test fixture were designed by John Addis for the 485 scope (Note 1), which uses no less than 18 of these chips in various grades.
The last two digits of the part number, the grade, correspond to a combination of DC and HF performance. Each M84 was tested for DC performance and HF performance. DC performance was tested using a custom fixture described below. HF performance was tested using the 25ps Push-Pull Pulse Generator.
Suffix | Speed | DC Charact. | Replaceable by |
---|---|---|---|
00 | Fast | Best | ---- |
01 | Fast | Third best | -03,-00 |
02 | Fast | Most relaxed | -01,-03,-00 |
03 | Fast | Second best | -00 |
04 | Slow | Same as -00 | -00 |
05 | Slow | Same as -01 | -03,-00,-07,-04 |
06 | Slow | Same as -02 | -01,-03,-00,-05,-07,-04 |
07 | Slow | Same as -03 | -00,-04 |
10 | Fast | Best | ---- |
11 | Fast | Third best | -13,-10 |
12 | Fast | Most relaxed | -11,-13,-10 |
13 | Fast | Second best | -10 |
Sometimes an instrument will contain a better grade of part than called for in the manual.
The manual should be consulted for the correct replacement type. |
The M84 also comes in 14-pin DIP, as 155-0273-00 and 155-0274-00 (slower grade).
Regarding the various grades of M84, John Addis says:
There are several DC specs which differ with part suffix.
Suffixes -10, -11, -12 and -13 were used for the redesigned M84, known as the M705. The M705 was necessary because the original SH2 (2-2.5 GHz?) process was being discontinued. The M705 was designed by Hal Lillywhite using the faster SH3 process (6-7 GHz). Additionally, the M705 apparently had the gain setting resistor laser trimmed at the wafer level. The M705 was designed in late 1989 and tested in early 1990.
There was one high frequency test fixture and perhaps two dc test fixtures. Every M84 was subjected to all tests. All tests were done manually. I designed both test fixtures and the 25ps PPPG.
Transient Response (schematic not shown) uses the 25ps Push Pull Pulse Generator (PPPG) and a sampling scope. Sampler load supplies dc current (through X2 pads and sampler input resistance. The sampling scope chassis is floating at (probably) +5V through 8.2 ohms. 25ps PPPG has transformer coupled trigger output to sampling scope trigger input.
DC test fixture:
I have attached a schematic of a dc test fixture for manufacturing. It looks like this fixture only tests for Vhump. There may have been another test fixture for the other dc tests. Those tests may have been done on a system. The Vhump test may have been so difficult to perform on an automated system that it needed this extra fixture.
Vhump is the amount of maximum dc imbalance, probably referred to the input, which occurs when the variable gain function is swept from full invert to full normal. The two ends of the curve are set to the same dc output level using the balance control attached to pin 1. Ideally, there is no change in dc level under these conditions, but various imbalances in the M84 output devices result in a hump for inverted gain and a hump for the normal gain. Only the -00, -04 and -10 suffixed parts were required to pass this stringent Vhump test. The fixture was in a rubber footed metal chassis about 4” high 5” deep, and 7” wide.
Test criteria defining the various grades of M84: Displayed Risetime <355 ps -00 and -10 -01 and -11 -02 and -12 -03 and -13 Displayed Risetime 355-410 ps -04 -05 -06 -07 Normal Offset (RTO) <14 mV <14 mV <28 mV <14 mV Invert Offset (RTO) <14 mV <14 mV <28 mV <14 mV HFE of Q1 and Q2 70-250 70-250 50-400 70-250 Normal Gain 2.68-2.96 2.68-2.96 2.68-2.96 2.68-2.96 Invert Gain 2.68-2.96 2.68-2.96 2.68-2.96 2.68-2.96 Null Offset (Gain = 0) 10 mV no spec no spec <30 mV Null Gain (Test of Q3 and Q4) 14 mV no spec no spec <14 mV 50% Gain 0.49-0.51 no spec no spec 0.49-0.51 Off Feedthrough <0.2 mV <0.2 mV <0.2 mV <0.2 mV Normal Hump Voltage <2.5 mV no spec no spec no spec Invert Hump Voltage <2.5 mV no spec no spec no spec
See also
- 234-0203-20: SH3 version
Patents that may apply to 155-0078-00
Page | Title | Inventors | Filing date | Grant date | Links |
---|---|---|---|---|---|
Patent US 3633120A | Amplifier circuit | Carl Battjes | 1970-09-16 | 1972-01-04 | Ft doubler • 155-0061-00 • 203-0126-90 • 155-0064-00 • 155-0078-00 • 155-0080-00 • 155-0175-00 • 155-0178-00 • 155-0181-00 • 155-0187-00 |
Pictures
-
Excerpt from 067-0587-01 schematic, showing application of 155-0078-00.
-
155-0078-01 amplifiers in 7A26. Note symmetric layout.
-
M84 Hump Voltage Test Fixture schematic
-
155-0078-10
-
155-0078-10
Used in
- 464, 465, 466, 468
- 475 (U140, U240, U450), 475A, 475M
- 485
- 2220, 2221, 2230 (155-0274-00: A1U130, A1U180; 155-0273-00: A2U30, A2U80)
- 7834, 7844 (U415,U515)
- 7854 (A13U520,A13U590,A13U620,A13U680)
- 7904, R7903 (U5510,U5530,U5550,U5610,U5630,U5650)
- R7912, 7912AD, 7912HB
- 7104
- 7A16A (U350, U450, U550, U750), 7A16P (U60240, U60340, U60440, U60540)
- 7A24, 7A26 (U1350,U1450,U1550,U1750,U2350,U2450,U2550,U2750)
- 7A26
- 7A42 (A5U1010,A5U1020,A5U1040,A5U1060)
- 067-0587-01, 067-0680-00
- AM503
- PG502 (U360, -06)
- PG508 (U850)
- DC510 (A12U1311, A12U1331, -10), DC5010
- FG5010
Some instruments using part 155-0078-00
Instrument | Manufacturer | Class | Model | Description | Introduced |
---|---|---|---|---|---|
067-0587-01 | Tektronix | Plug-in | 067-0587-01 | 7000 Series Calibration Fixture | (?) |
067-0680-00 | Tektronix | Plug-in | 067-0680-00 | 5400 Series Mainframe Calibrator | (?) |
464 | Tektronix | Oscilloscope | 464 | Portable 100 MHz dual-trace storage scope | 1975 |
465 | Tektronix | Oscilloscope | 465 | Portable 100 MHz dual-trace scope | 1972 |
466 | Tektronix | Oscilloscope | 466 | Portable 100 MHz dual-trace storage scope | 1974 |
468 | Tektronix | Oscilloscope | 468 | 10/100 MHz Digital Storage Scope | 1980 |
475 | Tektronix | Oscilloscope | 475 | Portable 200 MHz dual-trace scope | 1972 |
475A | Tektronix | Oscilloscope | 475A | Portable 250 MHz dual-trace scope | 1977 |
485 | Tektronix | Oscilloscope | 485 | 350 MHz portable scope | 1972 |
7104 | Tektronix | Oscilloscope | 7104 | 1 GHz mainframe with MCP CRT | 1978 |
7834 | Tektronix | Oscilloscope | 7834 | 400 MHz storage mainframe | 1977 |
7844 | Tektronix | Oscilloscope | 7844 | 400 MHz dual-beam non-storage mainframe | 1974 |
7854 | Tektronix | Oscilloscope | 7854 | 400 MHz waveform-processing scope | 1980 |
7904 | Tektronix | Oscilloscope | 7904 | 500 MHz non-storage mainframe | 1971 |
7912AD | Tektronix | Oscilloscope | 7912AD | 500 MHz digitizer | 1978 |
7912HB | Tektronix | Oscilloscope | 7912HB | 750 MHz digitizer | 1988 |
7A16A | Tektronix | Plug-in | 7A16A | 225 MHz vertical amplifier | 1973 |
7A16P | Tektronix | Plug-in | 7A16P | 150/200 MHz vertical amplifier | 1978 |
7A24 | Tektronix | Plug-in | 7A24 | 400 MHz dual channel vertical amplifier | 1974 |
7A26 | Tektronix | Plug-in | 7A26 | 200 MHz dual-channel amplifier | 1974 |
7A42 | Tektronix | Plug-in | 7A42 | 350 MHz four-channel logic triggered amplifier | 1984 |
AM503 | Tektronix | Plug-in | AM503 | current probe amplifier | 1976 |
DC5010 | Tektronix | Plug-in | DC5010 | 350 MHz programmable frequency counter | 1982 |
DC510 | Tektronix | Plug-in | DC510 | 350 MHz frequency counter | 1982 |
FG5010 | Tektronix | Plug-in | FG5010 | 20 MHz function generator | 1982 |
PG502 | Tektronix | Plug-in | PG502 | 250 MHz pulse generator | 1974 |
PG508 | Tektronix | Plug-in | PG508 | 50 MHz pulse generator | 1976 |
R7903 | Tektronix | Oscilloscope | R7903 | 500 MHz non-storage mainframe | 1974 |
R7912 | Tektronix | Oscilloscope | R7912 | 500 MHz digitizer | 1973 |
Notes
- Note 1: See John Addis quote in 7A11 article