5CT1N: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
 
(28 intermediate revisions by 3 users not shown)
Line 1: Line 1:
Curve Tracer Plug-in for the 5000 series oscilloscopes.
{{Plugin Sidebar
|manufacturer=Tektronix
|series=5000-series scopes
|type=5CT1N
|summary=Curve tracer plug-in
|image=5ct1n-crop.jpg
|caption=5CT1N curve tracer
|introduced=1972
|discontinued=1988
|designers=Matt Zimmerman
|manuals=
* [[Media:070-1246-00.pdf|Tektronix 5CT1N Manual (split schematics, grayscale)]]
* [[Media:5CT1N Schematic.pdf|Tektronix 5CT1N Schematic (whole, color)]]
}}
The '''Tektronix 5CT1N''' is a curve tracer plug-in for the 5000 series oscilloscopes, similar to the [[7CT1N]] for [[7000-series scopes]].
The 5CT1N was designed by [[Matt Zimmerman]].


Common Problems
{{BeginSpecs}}
{{Spec | DUT drive voltage (C-E) |
* positive (NPN or N channel) or negative (PNP or P channel) half-waves
* 7.5 V, 0.5 V/Div, 240 mA peak
* 30 V, 2 V/Div, 60 mA peak
* 75 V, 5 V/Div, 24 mA peak
* 300 V, 20 V/Div, 6 mA peak
* HV warning light on for > 50 V
* peak power 500 mW}}
{{Spec | DUT current display  |
* 10 μA/Div to 20 mA/Div, 1−2−5 steps (x 1 mode)
* 10 nA/Div to 20 μA/Div, 1−2−5 steps (x 1000 mode)}}
{{Spec | Base/Gate drive |
* 0 to at least 10 steps
* dual polarity
* variable offset, at least +/− 5 steps
* current mode: 1 μA/Step to 1 mA/Step in 1−2−5 sequence
* voltage mode: 1 mV/Div to 1 V/Div in 1−2−5 sequence, 1 kΩ current limit
}}
{{Spec | DUT connection | Three 4 mm jacks / binding posts}}
{{Spec | DUT adapters |
* [[013-0072-00]] Axial diodes
* [[013-0069-00]] Devices with long leads
* [[013-0070-01]] Transistors in TO-3 or TO-66 cases
* [[013-0074-00]] Transistors with stud leads
* [[013-0110-00]] Diodes with stud leads
* [[013-0112-00]] Transistors in TO-36 cases
* [[013-0128-00]] Transistors in TO-5 or TO-18
}}
{{EndSpecs}}


C30 and C32 (100 uF, 25V) have a tendency to leak or short, causing associated resistors R30 and R32 (240, .25W, 5%) to overheat and fail. A good preventative maintenance procedure would be to replace these two capacitors with modern equivalents. Two 5CT1N units purchased online had this fault, and replacement of the capacitors and resistors restored proper operation.
==Links==
* [http://www.ke5fx.com/A_VTCT_Adapter_for_All_Tektronix_SCTs_W7PF.pdf Dennis Tillman: An Inexpensive Vacuum Tube Curve Tracer Adapter for All Tektronix Semiconductor Curve Tracers]
{{Documents|Link=5CT1N}}
{{Documents|Link=Curve tracers}}
{{PatentLinks|5CT1N}}
 
==Pictures==
<gallery>
5440.jpg | 5CT1N in [[5440]] mainframe vertical bay, X output connected to time base X input
Tek-5ct1_in_use.jpg| Displaying transistor curves
Tek 5ct1n f1.JPG
Tek 5ct1n front2.jpg
5CT1N 7CT1N Basic Measurement Reference Chart.jpg
</gallery>
 
==Common Problems==
 
C30 and C32 (100 μF, 25 V) [http://hakanh.com/dl/docs/hardtofind/CT1N.pdf are under-rated] and therefore have a tendency to leak or short,  
causing associated resistors R30 and R32 (240 Ω, 0.25 W, 5%) to overheat and fail.  
C30 and C32 should be replaced with modern equivalents rated above 35 V.  
 
==Components==
{{Parts|5CT1N}}
 
[[Category:Curve tracers]]
[[Category:5000 series plugins]]

Latest revision as of 02:17, 16 October 2024

Tektronix 5CT1N
Curve tracer plug-in
5CT1N curve tracer

Compatible with 5000-series scopes

Produced from 1972 to 1988

Manuals
Manuals – Specifications – Links – Pictures

The Tektronix 5CT1N is a curve tracer plug-in for the 5000 series oscilloscopes, similar to the 7CT1N for 7000-series scopes. The 5CT1N was designed by Matt Zimmerman.

Key Specifications

DUT drive voltage (C-E)
  • positive (NPN or N channel) or negative (PNP or P channel) half-waves
  • 7.5 V, 0.5 V/Div, 240 mA peak
  • 30 V, 2 V/Div, 60 mA peak
  • 75 V, 5 V/Div, 24 mA peak
  • 300 V, 20 V/Div, 6 mA peak
  • HV warning light on for > 50 V
  • peak power 500 mW
DUT current display
  • 10 μA/Div to 20 mA/Div, 1−2−5 steps (x 1 mode)
  • 10 nA/Div to 20 μA/Div, 1−2−5 steps (x 1000 mode)
Base/Gate drive
  • 0 to at least 10 steps
  • dual polarity
  • variable offset, at least +/− 5 steps
  • current mode: 1 μA/Step to 1 mA/Step in 1−2−5 sequence
  • voltage mode: 1 mV/Div to 1 V/Div in 1−2−5 sequence, 1 kΩ current limit
DUT connection Three 4 mm jacks / binding posts
DUT adapters

Links

Documents Referencing 5CT1N

Document Class Title Authors Year Links
Tekscope 1971 V3 N5 Sep 1971.pdf Article New Products 1971
Tekscope 1972 V4 N6 Nov 1972.pdf Article Oscilloscope to Curve Tracer with One Plug-in Matt Zimmerman 1972
48W-3346-3.pdf Brochure Making the Correct Semiconductor Measurements Time After Time 1982

Documents Referencing Curve tracers

Document Class Title Authors Year Links
062-1009-00.pdf Book Measurement Concepts: Semiconductor Device Measurements John Mulvey 1969
Tekscope 1969 V1 N1 Feb 1969.pdf Article Curve Tracing Displays 1969
Tekscope 1969 V1 N5 Oct 1969.pdf Article Troubleshooting the Sweep Ciruits Charles Phillips 1969
Tekscope 1972 V4 N3 May 1972.pdf Article Semiautomatic Testing with the Curve Tracer Jack Millay 1972
Tektronix Curve Tracers - Device Testing Techniques.pdf Book Tektronix Curve Tracers - Device Testing Techniques 1985

Pictures

Common Problems

C30 and C32 (100 μF, 25 V) are under-rated and therefore have a tendency to leak or short, causing associated resistors R30 and R32 (240 Ω, 0.25 W, 5%) to overheat and fail. C30 and C32 should be replaced with modern equivalents rated above 35 V.

Components

Some Parts Used in the 5CT1N

Part Part Number(s) Class Description Used in
2N3958 151-1054-00 151-1054-01 151-1054-02 Discrete component dual n-channel JFET FG503 MR501 M3 PG505 SC501 SC502 SC503 SG502 1450 1501 1502 1503 221 5A23N 5CT1N 577 603 603A 604 604A 605 606 606A 606B 607 607A 620 624 7CT1N 7D15 7D20 851