4S2: Difference between revisions
No edit summary |
No edit summary |
||
| (5 intermediate revisions by 2 users not shown) | |||
| Line 16: | Line 16: | ||
* [https://w140.com/tek_fcp/tek_type_4s2_factory_cal_proc.pdf Tektronix 4S2 Field Recalibration Procedure] | * [https://w140.com/tek_fcp/tek_type_4s2_factory_cal_proc.pdf Tektronix 4S2 Field Recalibration Procedure] | ||
* [https://w140.com/tek_fcp/tek_type_4s2_tentative_factory_cal_proc.pdf Tektronix 4S2 Factory Calibration Procedure] | * [https://w140.com/tek_fcp/tek_type_4s2_tentative_factory_cal_proc.pdf Tektronix 4S2 Factory Calibration Procedure] | ||
* [ | * [[Media:tek_4s2a_eng_spec.pdf|Tektronix 4S2A Engineering Spec]] (OCR) | ||
}} | }} | ||
The '''Tektronix 4S2''' is a two-channel [[sampling oscilloscope|sampling]] vertical plug-in for the [[661]]. | The '''Tektronix 4S2''' is a two-channel [[sampling oscilloscope|sampling]] vertical plug-in for the [[661]]. | ||
| Line 31: | Line 31: | ||
The 4S2 and 4S2A front panels look the same, but they use different GR-874 input connectors. | The 4S2 and 4S2A front panels look the same, but they use different GR-874 input connectors. | ||
The 4S2 uses a short airline unique to the 4S2. | The 4S2 uses a short airline unique to the 4S2. | ||
The 4S2A uses the connector-to-board system described in US Patent 3,426,311 | The 4S2A uses the connector-to-board system described in [[Patent US 3426311A|US Patent 3,426,311]] and has some parts in common with the [[3T7]]. | ||
The 4S2A uses a [[152-0252-00]] snap-off diode to generate the sampling pulse. | |||
{{BeginSpecs}} | {{BeginSpecs}} | ||
{{Spec | Bandwidth | DC to 3.9 GHz }} | {{Spec | Bandwidth | DC to 3.9 GHz }} | ||
| Line 85: | Line 86: | ||
Tek 4s2a gate board 2.jpg|4S2A Gate (Sampler) Board | Tek 4s2a gate board 2.jpg|4S2A Gate (Sampler) Board | ||
Tek 4s2a gate board.jpg | Tek 4s2a gate board.jpg | ||
Tek 661 4s2a 5t3 s-52.jpg|4S2A step response driven by [[S-52]]. 100 ps/div. | |||
</gallery> | </gallery> | ||
==Components== | |||
{{Parts|4S2}} | |||
{{Parts|4S2A}} | |||
[[Category:661 plugins]] | [[Category:661 plugins]] | ||
[[Category:Sampling plugins]] | [[Category:Sampling plugins]] | ||
[[Category:GR874]] | [[Category:GR874]] | ||
Latest revision as of 08:16, 19 August 2024
The Tektronix 4S2 is a two-channel sampling vertical plug-in for the 661. Signals enter the 4S2 through GR-874 connectors on the front panel.
Unlike the 4S1, the 4S2's signal path does not contain a delay line between the input connector and the sampler. This has the advantage of maintaining higher pulse fidelity and thus higher bandwidth, but the disadvantage of making it impossible to see the leading edge of the triggering event unless a pre-trigger is used.
The 4S2, which was designed in 1962, uses a four-diode sampling bridge. The 4S2A, designed in 1965, uses a two-diode sampling bridge. This design change is discussed in the 4S2A Engineering Spec document linked below. The 4S2 does not provide trigger pick-off. The 4S2A provides trigger pick-off for channel A.
The 4S2 and 4S2A front panels look the same, but they use different GR-874 input connectors. The 4S2 uses a short airline unique to the 4S2. The 4S2A uses the connector-to-board system described in US Patent 3,426,311 and has some parts in common with the 3T7. The 4S2A uses a 152-0252-00 snap-off diode to generate the sampling pulse.
Key Specifications
| Bandwidth | DC to 3.9 GHz |
|---|---|
| Rise time | 90 ps |
| Deflection | 2 mV/Div to 200 mV/Div, 1−2−5 |
See Also
Pictures
4S2
-
4S2
-
4S2
-
4S2
-
4S2
-
4S2
-
4S2 Pulse Generator
-
4S2 Pulse Generator
-
4S2 Pulse Generator
-
4S2 Pulse Generator
-
4S2 Sampler
-
4S2 Sampler
-
AC Amplifier
-
AC Amplifier
-
Memory
-
Memory
-
Inverter
-
Inverter
-
Dual Trace
-
Dual Trace
-
4S2
-
4S2
-
4S2
-
4S2
-
4S2
-
4S2
-
4S2 Samplers
-
4S2 Top
-
4S2 Top Front
-
4S2 Top
-
Pulse Generator Card Removed, Var Gain Pots
-
4S2 Rear
4S2A
-
4S2A Front
-
42SA sampler schematic
-
42SA pulse generator schematic
-
4S2A Pulse Generator Front
-
4S2A Pulse Generator Rear
-
4S2A Gate (Sampler) Board
-
-
4S2A step response driven by S-52. 100 ps/div.
Components
Some Parts Used in the 4S2
Some Parts Used in the 4S2A
| Part | Part Number(s) | Class | Description | Used in |
|---|---|---|---|---|
| 152-0252-00 | 152-0252-00 | Discrete component | Tek-made step recovery diode | 4S2A |
| 6688 | 154-0215-00 | Vacuum Tube (Pentode) | miniature high-slope VHF/UHF pentode | P80 • 3T77 • 3T77A • 4S2A • 526 • TR-4602 |
| 7308 | 154-0371-00 | Vacuum Tube (Dual Triode) | dual triode | 3S76 • 3S3 • 4S1 • 4S2A • 4S3 • S-311 |