7CT1N

Tektronix 7CT1N
Curve tracer plug-in Tektronix 7CT1N Compatible with 7000-series scopes Produced from 1971 to 1990 Manuals Tektronix 7CT1N Manual (OCR) Semiconductor Device Measurements (Concepts series) (All manuals in PDF format unless noted otherwise)

Manuals – Specifications – Links – Pictures

The Tektronix 7CT1N is a curve tracer plug-in for 7000-series scopes. The 5CT1N plug-in for 5000-series scopes is very similar.

It can be installed in either a vertical or a horizontal compartment, a front-panel switch must be set accordingly. A pull-out cable with a plastic BNC plug connects to the input of a module installed in the corresponding plugin for the other axis, with a fixed 100 mV/div scaling compatible with time base X inputs.

Internally, a variable-amplitude 55 Hz triangle-wave source supplies a transformer to step up the drive voltage and decouple it from ground (Emitter terminal). A step source supplies base current or gate voltage to the DUT.

The amplifier for the current axis can be switched into a ÷1000 mode to detect leakage currents (of typical 1970s semiconductors, anyway).

Key Specifications

DUT drive voltage (C-E)	positive (NPN or N-channel) or negative (PNP or P-channel) half-waves 7.5 V, 0.5 V/div, 240 mA peak 30 V, 2 V/div, 60 mA peak 75 V, 5 V/div, 24 mA peak 300 V, 20 V/div, 6 mA peak HV warning light on for > 50 V peak power 500 mW
DUT current display	10 μA/div to 20 mA/div, 1−2−5 steps (×1 mode) 10 nA/div to 20 μA/div, 1−2−5 steps (÷1000 mode)
Base/Gate drive	0 to at least 10 steps dual polarity variable offset, at least +/− 5 steps current mode: 1 μA/step to 1 mA/step in 1−2−5 sequence voltage mode: 1 mV/step to 1 V/step in 1−2−5 sequence (via 1 kΩ current limiting resistor)
DUT connection	Three 4 mm jacks / binding posts
DUT adapters	013-0072-00 Axial diodes 013-0069-00 Devices with long leads 013-0070-01 Transistors in TO-3 or TO-66 cases 013-0074-00 Transistors with stud leads 013-0110-00 Diodes with stud leads 013-0112-00 Transistors in TO-36 cases 013-0128-00 Transistors in TO-5 or TO-18

Links

Documents Referencing 7CT1N

Document	Class	Title	Authors	Year	Links
Tekscope 1971 V3 N5 Sep 1971.pdf	Article	New Products		1971	7L12 • 7CT1N • 5103N • 5A13N • 5A14N • 5A22N • 5CT1N • 172 • 1501 • P6056 • P6057 • 603 • 604 • 4602 • S-3160
Tekscope 1972 V4 N6 Nov 1972.pdf	Article	Oscilloscope to Curve Tracer with One Plug-in	Matt Zimmerman	1972	5CT1N • 7CT1N
7000 series brochure March 1973.pdf	Brochure	7000 series brochure, March 1973		1973	7A11 • 7A12 • 7A13 • 7A14 • 7A15A • 7A16A • 7A17 • 7A18 • 7A19 • 7A21N • 7A22 • 7B50 • 7B53A • 7B70 • 7B71 • 7B92 • 7CT1N • 7D11 • 7D13 • 7D14 • 7D15 • 7M11 • 7L12 • 7S11 • 7S12 • 7T11 • 7704A • R7704 • 7904 • R7903 • 7603 • R7603 • 7403N • R7403N • 7313 • R7313 • 7613 • R7613 • 7623 • R7623 • P7001
48W-3346-3.pdf	Brochure	Making the Correct Semiconductor Measurements Time After Time		1982	576 • 172 • 176 • 577 • 178 • 5CT1N • 7CT1N

Documents Referencing Curve tracers

Document	Class	Title	Authors	Year	Links
062-1009-00.pdf	Book	Measurement Concepts: Semiconductor Device Measurements	John Mulvey	1969	Curve tracers • Tunnel diodes
Tekscope 1969 V1 N1 Feb 1969.pdf	Article	Curve Tracing Displays		1969	Curve tracers • 576
Tekscope 1969 V1 N5 Oct 1969.pdf	Article	Troubleshooting the Sweep Ciruits	Charles Phillips	1969	575 • 576 • Curve tracers
Tekscope 1972 V4 N3 May 1972.pdf	Article	Semiautomatic Testing with the Curve Tracer	Jack Millay	1972	576 • 172 • Curve tracers
Tektronix Curve Tracers - Device Testing Techniques.pdf	Book	Tektronix Curve Tracers - Device Testing Techniques		1985	Curve tracers • Tunnel diodes

Common Problems

C30 and C32 (100 μF, 25 V) are under-rated and therefore have a tendency to leak or short, causing associated resistors R30 and R32 (240 Ω, 0.25 W, 5%) to overheat and fail. C30 and C32 should be replaced with modern equivalents rated above 35 V.