7L18

Manuals – Specifications – Links – Pictures

The Tektronix 7L18 is a spectrum analyzer plug-in introduced in 1978 for 7000-series scopes. It occupies three plug-in bays in the oscilloscope.

Key Specifications

Frequency range	1.5 GHz to 18 GHz with the internal mixer, 12.5 GHz to 60 GHz using external mixers
Frequency span	0; 200 Hz/Div to 500 MHz/Div in 1−2−5 steps; Max (see note below)
Resolution bandwidth	30 Hz to 3 MHz in decade steps
Vertical scale	10 dB/Div, 2 dB/Div, or linear
Input attenuator	0 dB to 60 dB in 10 dB steps
Sweep	1 μs/Div to 20 s/Div, auto, ext, or manual
Digital functions	two memory banks (A, B); Display A, B - A saved, peak hold

Please expand

Context

Linley Gumm says:

Another disappointment was the 7L18 microwave analyzer project, one of the earliest Tek products to have a microprocessor in it.

"We started work on developing this product in 1974, and finally shipped our first instrument in 1978. As I look back, it was a terribly crude microprocessor, and we made every error in the book. Of course, we didn't have any of the tools that are available today."

Although the 7L18 never did sell well, Linley and his crew developed components and technologies that later were used in the 492. (TekWeek March 27, 1987)

As Project Manager for the 7L18 I would like to express my thanks to those who contributed so much to the success of the project. Bob Bales worked on the sweep, span attenuator, YIG driver, and instrument-interconnect; Russell Brown and George Maney did the microprocessor programming; Carlos Beeck and James Wolf mechanical design of the microwave assemblies, with Dave Shores and Philip Snow providing the electrical design; IF design was done by Wesley Hayward; Jack Reynolds was involved in the early design of the phase lock circuitry with Steve Morton completing the work; Don Kirkpatrick designed the digital storage IC's with Dennis Smith doing the front panel and digital storage board; Al Huegli was responsible for the outstanding job of mechanical design. Virginia Morehead was indispensable in providing prototype support, as were the plant support people during introduction. Many other names should be included in this list but space doesn't allow. Mv thanks to each

Internals

The LO is a YIG tuned oscillator covering the 2 GHz to 4 GHz range. Its output passes through a sampler assembly used to PLL the YIG on small resolution bandwidths. The output of the sampler goes to the LO input on the mixer. The mixer IF output is 510 MHz.

The 7L18's components are controlled by an Intel 4004 4-bit microprocessor.

The 7L18 will NOT do 1.5 GHz to 18 GHz in one span, it will only max span the range selected by the BAND/HARMONIC control. This range is determined by the heterodyne harmonic number and sign (sideband) and the range of the first LO, which is 2 GHz to 4 GHz.

The input attenuator is a standard Weinschel Engineering product driven by a belt. The range is encoded for the digital dBm reference level display. The signal then passes through a YIG preselector filter with a 50 MHz bandwidth. After the YIG filter, the signal enters the RF input of the mixer assembly.

Links

• TekScope Vol. 9 No. 3, 1977
• Spectrum Analysis Using Waveguide Mixers
• Waveguide Mixers for 492 and 7L18

Prices

Year	1978	1980	1982	1984
Catalog price	$12,600	$14,600	$17,500	$19,400
In 2023 Dollars	$59,300	$54,400	$55,700	$57,300

Pictures

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 

Service views:

• 

  Top view

• 

  Bottom view

• 

  Service setup for the right front panel

Boards within the digital card cage (from back to front):

• 

  CRT Readout board

• 

  Center Freq Readout board

• 

  Sweep Horiz board

• 

  Span Atten board

• 

  Phase Lock module, rear

• 

  Phase Lock module, front

• 

  Phase Lock Logic CTL

• 

  VR Noise Filter

• 

  Log & Video Amp

• 

  Center Freq DVM

• 

  Digital Storage, front

• 

  Digital Storage, back

• 

  Micro Computer

The microcomputer board is built using three very old Intel chips: an Intel 4004 processor, an Intel 4002 320-bit RAM and 4-bit output port, and an Intel D4289 standard memory interface. The D4289 connects the 4004 to the two 2K8 ROMs. Note that in an earlier version of the 7L18 there were 6 ROMs.

Internal views of the analog parts:

• 

  Internal of the LO sampler