7104

Manuals – Specifications – Links – Pictures

The Tektronix 7104 is a 1 GHz, non-storage 7000-series oscilloscope mainframe that takes two 7000-series vertical plug-ins and two 7000-series horizontal plug-ins. It was introduced in 1978. There is also a rack-mount version, the R7103, albeit with only one horizontal bay.

The scope employs a micro-channel plate (MCP) CRT design to get good screen intensity at high sweep speeds with moderate acceleration voltage. The benefit is especially noticeable at low repetition rates.

The high horizontal speed necessitated using distributed deflection plates also for the horizontal deflection system, which reaches a bandwidth of 350 MHz. Option 2 adds a horizontal delay line to make the high horizontal bandwidth available for X-Y mode at a phase shift of <2° up to 50 MHz, nullable at any frequency up to 250 MHz.

The 7A29 1 GHz vertical amplifier and the 7B15/7B10 time base pair were introduced along with the 7104 to match the system bandwidth.

Val Garuts was the initial project leader. Gene Andrews took over the project lead about half way through the seven year development. John Addis was the Project Engineer for the vertical system. He designed the 7A29 plugin and its H500 and H476 ICs (the latter was also used in the 7104 mainframe). Wink Gross designed the 7104 main vertical amplifier including the channel switch, the main vertical output amplifier and its H477 IC. Dave Morgan designed the mainframe horizontal amplifier, and Art Metz designed the Z axis system. Dennis Hall was the project leader for the CRT. Aris Silzars designed the vertical deflection plate structure and managed the acquisition of the microchannel plate. Conrad Odenthal designed the box lens for the CRT.

Key Specifications

Bandwidth	1 GHz (with 7A29) – rise time < 350 ps
Fastest calibrated sweep	200 ps/Div (with 7B10)
Calibrator	40 mV to 4 V (p-p) in decade steps, 1 kHz; 4 mV to 400 mV into 50 Ω; 40 mA with adapter
Y delay line	51 ns (frequency compensated coax pair)
X-Y phase shift	base model: < 2° from DC to 50 kHz Opt. 2: < 2° from DC to 50 MHz (with a pair of 7A19 or 7A29, at least one of which has the variable delay option)
Acceleration voltage	12.5 kV
CRT	T7100-31-2 Micro channel plate CRT (154-0783-00), P31 phosphor, 8 × 10 Div. @ 8.5 mm, resolution 17 lines / Div., vertical 2 GHz bandwidth @ 1 V/Div sensitivity
Power consumption	215 W
Dimensions	345 mm (h) × 305 mm (w) × 592 mm (l)
Weight	19.8 kg (43.6 lb)
Features	Readout 2 probe power connectors
Options	Opt.02 – X-Y Horizontal Compensation Opt.03 – EMI modification

MCP protection

The Micro Channel Plate's amplification degrades irreversibly with operation, in proportion to the log of total charge passed per display area. For this reason, continued operation with a steady trace and especially at large beam currents must be avoided. The 7104 should not be used with plug-ins that generate a slow continuous sweep, or vector graphics. This includes sampling plug-ins, spectrum analyzers, logic analyzers, and the 7D20 digitizer.

The 7104 contains a "limited viewing time" circuit to assist with observing this restriction. At beam currents above 0.2 μA, a yellow indicator illuminates, and the beam will be shut down after 20 minutes. The limit time drops to two minutes at an average beam current of 2 μA, and also limits the average current to that value. Single-shot display current is not affected.

Despite this limiter, older instruments often exhibit darkening of the screen around the horizontal center line to some degree (see screen shot).

Internals

The 7104 makes extensive use of custom integrated circuits and hybrid circuits, inter alia, the 155-0174-00 Delay Line Compensator, 155-0173-00 Vertical Channel Switch, 155-0176-00 Vertical Output Amplifier, 155-0194-00/01/02/03 CRT Termination, 155-0175-00 Trigger Amplifier, 155-0178-00 Horizontal Output Amplifier, 155-0012-00 Z-Axis controller/amplifier, and 155-0067-02 SMPS controller. The high-speed amplifiers use Hypcon ceramic packages that use elastomer-based frames for coupling chip connections to the circuit board at constant impedance. The signal connections are differential throughout, and the signal path was optimized for matching and low reflection, including the plugin to mainframe card-edge connectors and the use of stripline and coplanar waveguide techniques right up to the CRT.

The 7104's amplifiers use a then novel scheme of "feed-beside" compensation (US Pat. 4.132.958) where instead of matching the HF response to the LF response, the LF response is determined by off-the-shelf operational amplifiers in parallel to the high-speed amplifiers, with a number of adjustable R-C time constants to compensate for thermal and other LF effects. The same technique is employed in the 7A29 amplifier plug-in.

Power Supply

The 7104 uses a switch-mode power supply.

Module A23 (schematic page <14>) contains the mains rectifier, base drive circuitry, and power transistors of the inverter (aka, switcher). These transistors produce a 25 kHz waveform that is fed to the primary of T1310 (120-1183-00), whose secondaries provide the power for the rest of the scope.

Module A24 (also on schematic page <14>) contains the inverter control circuit and rectifiers for the secondaries of T1310. The inverter control circuit uses the 155-0067-02 inverter control IC, which is U1275.

Module A25 (schematic page <15>) contains the low-voltage regulators. There are independently regulated and current-limited sections for the −50 V, −15 V, +5 V, +15 V and +50 V rails. Each section has an opamp and a BJT output transistor in emitter-follower configuration.

The opamps need power, too. To avoid a dependency cycle, the power supplies for the opamps are separate low-current, low-efficiency zener clamps that in no way depend on the −50 V, −15 V, +5 V, +15 V or +50 V regulators. The power supplies for the opamps produce −22 V, −5.6 V, +5.6 V, and +22 V. To avoid exceeding the opamps' limit of 30 V total rail voltage, each opamp either gets −22 V and +5.6 V, or −5.6 V and +22 V, depending on whether it needs more output swing in the positive or negative direction.

The +50 V section produces the reference voltage ("50VS") for the other sections. It uses a 9 V zener diode, VR1412, as a reference.

The dependency relationship of the supplies is:

• The −50 V, −15 V, +5, and +15 V sections depend on
  • the +50 V supply for reference voltage,
  • the opamp supplies for to power their opamps, and
  • the A24 semi-regulated rectifier outputs
• The +50 V depends on
  • the opamp supplies (+22 V and −5.6 V) for to power its opamp,
  • the A24 semi-regulated rectifier outputs (−54 and +54 V)
• The opamps supplies depend on
  • the A24 semi-regulated rectifier outputs
• The semi-regulated rectifier outputs depend only on mains power to enter tick/burst mode. However, to enter normal mode, a variety of things need to be working properly.

Prices

	Year	1980	1984	1990
Mainframe only	Catalog price	$14,400	$21,380	$29,995
	In 2023 Dollars	$53,700	$63,200	$70,500
Mainframe with 7A29, 7A29 Opt. 04, 7B15, 7B10	Catalog price	$21,730	$31,875	$44,510
	In 2023 Dollars	$81,000	$94,200	$104,600

Links

• Hans Springer's 1979 Electronic Design article on the 7104
• Reading Jim Williams: Scope Sunday 4
• Tek 7104 @ amplifier.cd
• Tek 7104 @ barrytech.com
• A Tektronix oscilloscope that moved faster than light? The Oregonian, 23 Sep 2011. (Original no longer accessible, link via archive.org.)
• Tektronix 7104 @ radiomuseum.org

Documents Referencing 7104

Document	Class	Title	Authors	Year	Links
Tekscope 1979 V11 N1.pdf	Article	1 GHz at 1 mV in a General Purpose Plug-in Oscilloscope	Hans Springer	1979	7104 • Hypcon • SHFIII • 7A29 • 7B10 • 7B15

Pictures

• 

  7104 front view (operating)

• 

  7104 with camera mounting frame on cart

• 

  Front with empty plug-in bays

• 

  Plug-in bays

• 

  Rear view of 7104

• 

  Rear view of 7104

• 

  Probe power outlets

• 

  CRT label

• 

  CRT label

• 

  CRT Circuit

• 

  CRT Circuit

• 

  Front outputs

• 

  Readout board

• 

  Interior right side

• 

  7104 horizontal (top) and vertical (bottom) output amplifiers

• 

  Vertical amplifier

• 

  Vertical amplifier close-up

• 

  Vertical amplifier, final stage close-up

• 

  Vertical CRT interconnect

• 

  Horizontal amplifier

• 

  7104 horizontal output amplifier, CRT connection and termination of distributed horizontal deflection plates

• 

  Rear right (vertical channel switch board and mainframe interconnect)

• 

  7104 vertical channel switch board

• 

  7104 vertical channel switch board

• 

  The upper half of the 7104 can be tilted upward for service. A metal support is included, like on the hood of a car.

Measurements

• 

  Rise time measurement. 150 ps risetime pulse from 067-0587-02 at 100 Hz repetition rate. Measured 240 ps (corrected for 150 ps fixture rise time: 190 ps = 1.8 GHz)

• 

  Rise time measurement as before, 1000 Hz repetition rate at same brightness settings.

• 

  7104 recording a single shot pulse (from 067-0587-02) at 200 ps/Div. Camera: Nikon D7000, 50 mm f/1.4, ISO 3200, 1/2 s. CRT filter not removed.

• 

  7104 recording 1 GHz sine, single sweep at 500 ps/Div. Camera: Nikon D7000, 50 mm f/1.4, ISO 3200, 1/2 s manually released. CRT filter not removed. CRT amplification loss is evident around the center line.

• 

  Faster-than-light beam on 7104? Using a 067-0587-02 calibration fixture at maximum amplitude produces this trace spanning 1.2 Div horizontally at 200 ps/Div and 8 Div vertically. Trace length is (1.2² + 8²)^½ × 8.5 mm = 68.8 mm, travelled in 1.2 × 200 ps = 240 ps. Apparent speed is therefore 68.8×10^-3 / 240×10^-12 m/s or 2.86×10⁸ m/s. 95.6% c₀ - a very near miss ...

Components

Some Parts Used in the 7104

Custom ICs used in the 7000 series readout system

Page	Model	Part nos	Description	Designers	Used in
155-0014-01	M019D	155-0014-00 • 155-0014-01	analog-to-decimal converter	Barrie Gilbert	7000 series readout system • 7854 • 7934 • 7J20 • 7L5 • P7001
155-0015-01	M020F	155-0015-00 • 155-0015-01	analog data switch	Barrie Gilbert	7000 series readout system • 7854 • 7934
155-0017-00	M025	155-0017-00	5 MHz decade counter	Barrie Gilbert	7000 series readout system • 7854 • 7934
155-0018-00	M026	155-0018-00	zeros logic control	Les Larson	7000 series readout system • 7934
155-0019-00	M027	155-0019-00	decimal point and spacing control	Les Larson	7000 series readout system
155-0020-00	M028	155-0020-00	output assembler	Les Larson	7000 series readout system
155-0021-00	M029C	155-0021-00 • 155-0021-01	timing generator	Les Larson	7000 series readout system • 7854 • 7934
155-0023-00	M160	155-0023-00	character generator (0 1 2 3 4 5 6 7 8 9)	Barrie Gilbert	7000 series readout system
155-0024-00	M161	155-0024-00	character generator (↓ < I / + - + C Δ >)	Barrie Gilbert	7000 series readout system
155-0025-00	M162	155-0025-00	character generator (m μ n p X K M G T R)	Barrie Gilbert	7000 series readout system
155-0026-00	M163	155-0026-00	character generator (S V A W H d B c Ω E)	Barrie Gilbert	7000 series readout system
155-0027-00	M164	155-0027-00	character generator (U N L Z Y P F J Q D)	Barrie Gilbert	7000 series readout system