7844: Difference between revisions
No edit summary |
No edit summary |
||
| (One intermediate revision by the same user not shown) | |||
| Line 47: | Line 47: | ||
* [http://www.jvgavila.com/tek7844.htm Tek R7844 page @ EB5AGV], lots of internal photos | * [http://www.jvgavila.com/tek7844.htm Tek R7844 page @ EB5AGV], lots of internal photos | ||
{{Documents|Link=7844}} | {{Documents|Link=7844}} | ||
{{PatentLinks|7844}} | |||
==Internals== | ==Internals== | ||
| Line 102: | Line 103: | ||
Tek7844-front.jpg | Tektronix 7844 front view | Tek7844-front.jpg | Tektronix 7844 front view | ||
Tek7844-rear.jpg | Tektronix 7844 rear view | Tek7844-rear.jpg | Tektronix 7844 rear view | ||
Tektronix 7844.JPG | Tektronix 7844 (with Opt.03 CRT EMI screen) front view, [[7A26]], [[7A19]], [[7B80]] and [[7B85]] plug-ins | |||
7844-3.jpg | Simultaneous time and frequency domain display using a [[7A26]] amplifier, [[7B92A]] time base, and [[7L5]] Spectrum Analyzer | 7844-3.jpg | Simultaneous time and frequency domain display using a [[7A26]] amplifier, [[7B92A]] time base, and [[7L5]] Spectrum Analyzer | ||
R7844-2.jpg | Tektronix R7844 | R7844-2.jpg | Tektronix R7844 | ||
R7844-rear.jpg | Tektronix R7844, rear view | R7844-rear.jpg | Tektronix R7844, rear view | ||
Wellenkino 7844.jpg | 7844 with options 78 (blue P11 phosphor) and 21 (dedicated vertical slots, i.e. no vertical mode switch) | Wellenkino 7844.jpg | 7844 with options 78 (blue P11 phosphor) and 21 (dedicated vertical slots, i.e. no vertical mode switch) | ||
Tek 7844 with 7d15.JPG | | |||
Tek 7844 top.jpg | | Tek 7844 top.jpg | | ||
Tek 7844 rear connections.jpg | | Tek 7844 rear connections.jpg | | ||
Latest revision as of 13:14, 21 June 2024
The Tektronix 7844 is a 400 MHz dual-beam CRT oscilloscope that takes two 7000-series vertical plug-ins and two 7000-series horizontal plug-ins.
Versions include the 7844 bench-top lab scope and R7844 rack-mount model.
Circuit design for the 7844 was done by Chuck Scott, Dick Anderson, Keith Taylor, and Bob White. Project manager for the 7844 was Murlan Kaufman. The 7844's CRT was designed by Conrad Odenthal and Ken Hawken.
A typical configuration might have included 7A19 or 7A24 amplifiers, 7B80/7B85 or 7B92A timebases.
Key Specifications
| Bandwidth | 400 MHz with 7A19, 7A29 (eq. 0.9 ns rise time), 300 MHz with 7A24 |
|---|---|
| Fastest calibrated sweep | 1 ns/Div (with 7B80, 7B85, 7B92A) |
| Beam isolation | > 100:1 from DC to 150 MHz, > 30:1 from 150 MHz to 400 MHz |
| X-Y Phase Shift | < 2° from DC to min. 50 kHz |
| Horizontal bandwidth | DC to at least 1 MHz |
| Z axis input | 2 Vp-p for full intensity range (positive decreases), input impedance 500 Ω, rise time 15 ns, max. 1 MHz |
| CRT | T7840, p/n 154-0713-00 with P31 phosphor, or 154-0713-04 with P11 phosphor (Opt. 78), acceleration 24 kV (−3/+21) |
| Calibrator | 4 mV, 40 mV, 400 mV or 4 V into >100 kΩ, 0.4 mV, 4 mV, 40 mV or 400 mV into 50 Ω; 1 kHz |
| Power | 90-132 V or 180-264 V, 48 to 440 Hz, max. 235 W |
| Weight | 16.3 kg (36 lbs) / R7844: 15 kg (33 lbs) |
| Options |
|
Links
- Tek 7844 page at amplifier.cd and a repair report (switch-mode PSU)
- Tek 7844 @ barrytech.com
- R7844 page with frequency response measurements
- Tek R7844 page @ EB5AGV, lots of internal photos
Documents Referencing 7844
| Document | Class | Title | Authors | Year | Links |
|---|---|---|---|---|---|
| Tekscope 1974 V6 N4.pdf | Article | A 400-MHz Dual-Beam Oscilloscope | Murlan Kaufman | 1974 | 7844 • R7844 • T7840 |
Patents that may apply to 7844
| Page | Title | Inventors | Filing date | Grant date | Links |
|---|---|---|---|---|---|
| Patent US 3819984A | Side-by-side dual gun crt having horizontal deflector plates provided with side shields for correction of geometric distortion | Ken Hawken | 1973-02-12 | 1974-06-25 | T7840 • 7844 |
| Patent US 3921025A | Dual-beam CRT with vertical trace bowing correction means | Conrad Odenthal | 1974-07-05 | 1975-11-18 | T7840 • 7844 |
| Patent US 3983444A | Dual beam CRT with inner gun and outer gun shield means for correcting keystone distortion | Conrad Odenthal | 1975-10-24 | 1976-09-28 | T7840 • 7844 |
Internals
The 7844's CRT has distributed vertical deflection plates. It uses a number of custom ICs, such as 155-0064-00, 155-0065-00 and 155-0059-00 in the vertical amplifiers, 155-0095-00 in the vertical interface, 155-0078-00 in the trigger selector, and 155-0022-00 in the horizontal interface. The horizontal and Z axis amplifiers are discrete.
The 7844 is more complex than all other 7000 mainframes except the 7854 because vertical and horizontal amplifiers as well as the Z axis control boards exist twice, and there is an extra switching logic board. As a consequence, verifying correct operation requires testing many possible combinations of settings – for example, a defect on the vertical switching board could cause a problem only in the case of both beam 1 and 2 using horizontal bay B, but not if beam 1 used A and beam 2 used B. Moreover, calibration and adjustment is significantly more work than in a single-beam scope, e.g. CRT geometry trimpots need to be adjusted for matching both beams, not only for best geometry, and these adjustments even interact slightly.
The power supply is a resonant switch-mode inverter with linear post-regulation, similar to the one in the 7904. It uses the 155-0067-02 controller. Despite having an SMPS, the 7844 is fairly heavy behause of the duplicate internal components, especially the second vertical delay line. The delay lines need extra space and are located vertically to the right of the CRT instead of below the CRT as in other 7xx4s.
Unlike some other 7000 series mainframes with switchmode PSUs, the 7844 does have a fan.
Early 7844 (SN B109999 and earlier) have issues with horizontal aberrations for sweep rates of 1 ns/Div. After discovery of the issue modification kits (040-0804-00) that replace the horizontal amplifier were offered. For more information see the manual of the 067-0657-00 Normalized Ramp Generator that was use to investigate this issue.
Prices
| Year | 1976 | 1980 | 1984 | 1990 (R7844) | |
|---|---|---|---|---|---|
| Mainframe only | Catalog price | $6,100 | $9,125 | $13,435 | $19,500 |
| In 2023 dollars | $32,600 | $33,700 | $39,300 | $45,400 | |
| Mainframe with 2 × 7A19, 7B85, 7B80 |
Catalog price | $9,500 | $14,275 | $21,520 | $30,660 |
| In 2023 dollars | $50,800 | $52,700 | $63,000 | $71,300 |
Pictures
-
Tektronix 7844 front view
-
Tektronix 7844 rear view
-
-
-
Tektronix R7844
-
Tektronix R7844, rear view
-
7844 with options 78 (blue P11 phosphor) and 21 (dedicated vertical slots, i.e. no vertical mode switch)
-
-
-
-
-
Interior
-
Right interior. Top row: Calibrator board (l), readout board (c), beam 2 vertical amplifier (r), fan.
-
Right/above interior. The dual delay lines can be seen behind the readout board. Horizontally mounted boards in the center are: Crossover mode switch (l), trigger selector (c), power supply (r).
-
Beam 2 vertical amplifier, CRT and termination detail (right side)
-
Left interior. Beam 1 vertical amplifier (l), crossover vertical interface (r).
-
Left/above interior. Top row: Beam 1 Z axis (l), Beam 1 / Beam 2 horizontal amplifiers (c/r).
-
Vertical mode switch board, back side
-
Vertical mode switch board, back side (detail)
Option 22
-
An 7844 with option 22 (board right of the readout).
-
Opt. 22 board
-
Readout board (l), Opt. 22 board (r)
-
Opt. 22 board
Components
Some Parts Used in the 7844